Table of Contents
Advertisement
For proper printing, read "Directions for use" prior to the printing and comply with it.
G-code file is to be made using specific slicing software, so called Cubicreator (v2.5 and
G-Code
above)
preparation.
* Cubicreator must be set up for Cubicon Style (3DP-210F) Printer could be out of order if
you set up software for other printers.
Please use the authorized filament which HyVISION SYSTEM provides.
* It is excluded from warranty in case of the malfunction or damages caused by using 3rd
party filament which are not approved for Cubicon.
Filament
Please use the unsealed filament spool as soon as possible.
Keep your filament tightly wound on the spool and sealed.
* Using contaminated filament by humidity and dirty can cause the breakdown of printer
and printing quality problem.
Mounting
and
After mounting the filament considering the spool rotation/ insertion direction, turning the
Dismounting
of
label of spool outward.
filament spool
Make sure if the filament is loosened on the spool during dismounting it.
Take notice of Extruder temperature setting.
Replacement
of
* If the extruder temperatures are not set properly, nozzle blockage and filament grinding
Filament
can occur.
Loading &
When exchanging the filament, take notice of Extruder temperature setting and remove
Unloading
residuals inside of nozzle
Heat up the extruder (nozzle)/ heated bed to fit the proper temperature of filament.
* The printing quality can be improved by configuration of optimal value acquired through
Temperature
user experience.
condition
of
In case the temperature of filament is out of proper temperature range, bad printing quality
Extruder(Nozzle)
and breakdown of the printer such as carbonization, extruding failure, grinding, and
And Heated bed.
warping.
Remove the print object after the heated bed cools down accordingly.
Regularly clean the Extruder.
Open the cover of Extruder to remove the residue inside, contaminants of Gear, and
Extruder
filament path.
* Pay attention not to damage the internal wire when opening the cover of extruder to clean
inside.
Regularly check the extrusion condition and clean it.
* The replacement of worn nozzles due to normal use is excluded from the warranty
service.
After heating up the Extruder and clean the external nozzle of Extruder with pure cotton
Cleaning
of
cloth.
Extruder
and
* Clean the nozzle tips because its carbonized residue of filament may cause the error of
Nozzle
tilt align.
Pay attention not to damage the Extruder when cleaning the internal nozzle using Nozzle
Management Pin.
* Extruder failure can occur by improper use, so thoroughly become skilled.
Do not repeat cooling and heating while the filament remains inside of the nozzle.
Separating/
Be sure to turn off the power when separating or mounting the Extruder.
Mounting of the
Do not power down when the Extruder is heating up.
Extruder.
* It causes the damage to the internal circuitry because fan is not working.
Make sure not to cover the contaminants at the level point before Auto tilting.
* If the filament residue remains at the level point where calibrate the tilting, it may cause
the tilt align error. Please clean the contaminants at the level point before printing.
Clean the contaminants with scraper or dried cotton cloth.
Cleaning
the
* The replacement of damaged heated bed such as peeling off the coating due to normal
heated bed.
use is excluded from the warranty service.
Use the high purity acetone or water to clean the contaminated heated bed.
* Do not use wet wipes because washing ingredient of some wet wipes can contaminate
the coating of heated bed.
In case of Auto tilting failure, check if the nozzle touches the scope of level point and re-try
Auto tilt
the tilting after cleaning the heated bed and nozzle tip.
With the continuous error, please contact the official CS team to check and repair it.
Preparation of AS
Take a picture or video the malfunction status or inside of the printer or LCD Display.
request
* Users need to clarify the situation as much as possible to proceed the repair service.
Copyright Reserved HyVISION System Inc.
This document is Quick Start Guide (151001,En). To improve quality of product, this could be revised without
prior notification or consent.
HyVISION System is not liable for any losses resulted from the use of the document or any errors or offering.
Directions for use
3
Advertisement
Table of Contents
