Bronpi hydro series Installation, Operating And Servicing Instruction page 48

Sub-menu 03-04- Weekend Programme
In the same way as in the daily programme, this setting up has two independent
times to start and two to stop, with the precision that it only applies to Saturday and
Sunday. To access this setting up we need to start from the following screen (see
drawing D65).
We need to confirm the access to this programme by pressing button no.7 and it
should show the following screen (see drawing D66):
Modify the value "OFF" and select "ON": Finally, we introduce the time to start and
stop in order to complete the desired setting up.
As in the daily programme, if we need to set up only one time to start and stop, the
options START 2 and STOP 2 should indicate "OFF."
It is also possible to schedule one automatic start hour and manual stop hour (or vice
versa).
Example: START 1: 08:00 hours and STOP 1: "off"
or
START 1: "off" and STOP 1: 22:00 hours.
9.3.5 MENU 4. SELECT LANGUAGE
It allows selecting the languages from those available. To gain access to this menu
you have to confirm with button nº 7 and then, choose the selected language from
those available: Spanish, English, French, Italian, German and Portuguese with
buttons nº 1 and 2 (see drawing D67).
9.3.6 MENU 5. STAND-BY MODE
In case of thermo-stoves or insert, once the ambient or water temperature reaches
the temperature set plus a differential (2º C) by the user and it is activated "stand-by
mode" the thermo-stove will be automatically turned off (see drawing D68). When
the ambient temperature falls to the set temperature minus a differential (2ºC) the
thermo-stove automatically restarts an ignition cycle. It means that if you choose an
ambient temperature of 22ºC the thermo-stove or insert will turn-off when the room
temperature is 24º C and it will restart automatically when the ambient temperature
falls to 20ºC, regardless of the water temperature.
In case of the "Stand-by Mode" is deactivated (by default) the thermo-stove will work
by modulating the power when it reaches one of both temperatures, that allows the
temperature set could be higher.
9.3.7 MENU 6. SOUND MODE
By activating this mode, the thermo-stove or insert will emit a sound when the system detects a fault and goes
into the alarm state. To access to this menu you have to confirm with button nº 7 and then, choose "on" with
buttons nº 1 and 2 (see drawing D69).
9.3.8 MENU 7. INITIAL LOAD
In case that the thermo-stove has run out of fuel/pellets, in order to avoid a possible restart problem it is possible
to carry out a fuel pre-load for a maximum of 90 seconds to load the auger feeder. This can be used
when the thermo-stove is switched off and cold. To start the pre-load press button nº 2 and to stop it
press button nº 3. (see drawing D70).
It is very important that the burner is totally empty and clean when you start the thermo-stove or insert.
So, when the initial pre-load is finished, you must check the burner is clear of fuel in order to achieve correct
ignition of the thermo-stove.
9.3.9 MENU 8. CHOOSE PROBE
It allows us to select the probe to control the operation of the thermo-stove or insert (the one in the equipment or the one on the remote
control). It is advisable to select the option "Internal probe (thermo-stove or insert probe)" so that the thermo-stove or insert works depending
on the temperature where it is installed and not the temperature of the room where the remote control is. See drawing D71.
9.3.10 MENU 9. STOVE STATE
It shows the current state of the thermo-stove or insert and provides information about the devices connected. In this way, the user can get
some technical information. The next screens are seen automatically (see drawing D72, D73, D74).
9.4 USER MODE
Below is a description of the display in normal operation depending on the available functions.
Before ignition of the thermo-stove or insert the display shows the following screen (see drawing D75). It shows the "off" state, the room
temperature, the established working power and the current time.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
M-3-4
PROGRAMMME
WEEKEND
MENU
Menu 04
SPANISH
MENU
on
Menú 06
SOUND
MODE
MENU
47
off
M-3-4-01
PROGRAMME
WEEKEND
MENU
D65
D66
on
Menu 05
MODE
WAITING
MENU
D67 D68
76"
22º C
INITIAL
LOAD
MENU
D69
D70
Menu 08
CHOOSE
PROBE
MENU
D71
HYDRO SERIES RADIOFREQUENCY