Service Error Code - Canon mf6600 Series Service Manual

Service Error Code

■
Service Error Code
No. Tx/Rx
[Tx] at time of transmission, the procedural signal has been transmitted
##0100
more than specified.
[Tx/Rx]
##0101 the modem speed does not match that of the other party.
[Tx] at time of transmission, fall-back cannot be used.
##0102
[Rx] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).
##0103
[Tx] at time of transmission, RTN or PIN is received.
##0104
[Rx] at time of reception, the procedural signal is received for 6 sec while in
##0106
wait for the signal.
[Rx] at time of reception, the transmitting party cannot use fall-back.
##0107
[Tx] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or
##0109
CRP is received, and the procedural signal has been sent more than
specified.
[Tx/Rx]
##0111 memory error has occurred.
[Rx] at time of reception, RTN is transmitted.
##0114
[Rx] at time of reception, no image carrier is detected for 5 sec.
##0200
[Tx/Rx]
##0201 DCN is received outside the normal parity procedure.
[Tx/Rx]
##0220 system error (main program out of control) has occurred.
[Tx]
##0232 encoding error has occurred.
[Rx]
##0237 decoding error has occurred.
[Tx/Rx]
##0261 system error has occurred.
[Tx] at time of transmission, the procedural signal has been transmitted
##0280
more than specified.
[Tx] at time of transmission, the procedural signal has been transmitted
##0281
more than specified.
[Tx] at time of transmission, the procedural signal has been transmitted
##0282
more than specified.
[Tx] at time of transmission, the procedural signal has been transmitted
##0283
more than specified.
[Tx] at time of transmission, DCN is received after transmission of TCF.
##0284
[Tx] at time of transmission, DCN is received after transmission of EOP.
##0285
[Tx] at time of transmission, DCN is received after transmission of EOM.
##0286
[Tx]
##0287 at time of transmission DCN is received after transmission of MPS.
[Tx] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or
##0288
RTN has been received.
[Tx] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or
##0289
RTN has been received.
[Tx] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or
##0290
RTN has been received.
[Tx] at time of V.8 late start, the V.8 ability of DIS front the receiving party is
##0670
expected to be detected, and the CI signal is expected to be transmitted
in response; however, the procedure fails to advance, and the line is
released because of T1 timeout.
7
Error Codes > Fax Error Code > Service Error Code > Service Error Code
Description
7 Error Codes > Fax Error Code > Service Error Code > Service Error Code
No. Tx/Rx
[Rx] at time of V.8 arrival, procedure fails to move to phase 2 after detection
##0671
of CM signal from caller, causing T1 time-out and releasing line
[Tx] at time of V.34 transmission, a shift in procedure from phase 2 to phase
##0672
3 and thereafter stops, causing the machine to release the line and
suffer T1 timeout.
[Rx] at time of V.34 reception, a shift in procedure from phase 2 to phase 3
##0673
and thereafter stops, causing the machine to release the line and suffer
T1 timeout.
[Tx] at time of V.34 transmission, a shift in procedure from phase 3 and
##0674
phase 4 to the control channel and thereafter stops, causing the
machine to release the line and suffer T1 timeout.
[Rx] at time of V.34 reception, a shift in procedure from phase 3 and phase
##0675
4 to the control channel and thereafter stops, causing the machine to
release the line and suffer T1 timeout.
[Tx] at time of ECM transmission, no meaningful signal is received after
##0750
transmission of PPS-NULL, causing the procedural signal to be
transmitted more than specified.
[Tx] at time of ECM transmission, DCN is received after transmission of
##0752
PPS-NULL.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0753
more than specified after transmission of PPSNULL, or T5 time-out (60
sec) has occurred.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0754
more than specified after transmission of PPSNULL.
[Tx] at time of ECM transmission, no meaningful signal is received after
##0755
transmission of PPS-MPS, causing the procedural signal to be
transmitted more than specified.
[Tx] at time of ECM transmission, DCN is received after retransmission of
##0757
PPS-MPS.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0758
more than specified after transmission of PPS-MPS, or T5 time-out (60
sec) has occurred.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0759
more than specified after transmission of PPS-MPS.
[Tx] at time of ECM transmission, no meaningful signal is received after
##0760
transmission of PPS-EOM, causing the procedural signal to be
transmitted more than specified.
[Tx] at time of ECM transmission, DCN is received after transmission of
##0762
PPS-EOM.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0763
more than specified after transmission of PPS-MPS, or T5 time-out (60
sec) has occurred.
[Tx] at time of ECM transmission, the procedural signal has been transmitted
##0764
more than specified after transmission of PPSEOM.
[Tx] at time of ECM transmission, no meaningful signal is received after
##0765
transmission of PPS-EOP, causing the procedural signal to be
transmitted more than specified.
[Tx] at time of ECM transmission, DCN is received after transmission of
##0767
PPS-EOP.
7-5
Description
7-5