Canon iR C3380 series Service Manual page 533

IFXEML-Z Colour iFAX, E-Mail Rx print attribute flag function control
Switches attribute flags added to colour iFAX, E-Mail Rx prints.
Setting values
0: PDL text mode
1: PDL photograph mode
2: SCAN text mode
4: SCAN photograph mode
[Factory settings and after RAM clear: 0]
BMLNKS-Z BMLinks Rx print attribute flag function control
Switches attribute flags added to colour BMLinks Rx prints.
Setting values
0: SCAN photograph mode
1: PDL photograph mode
2: SCAN text mode
3: PDL text mode
[Factory settings and after RAM clear: 0]
DST-POS Setting the switching position for document scanning in DF mode (repeat reading)
Setting the document scanning position compensation when the glass surface is dirty
0: Position #1 + position #2
1: Position #1
2: Position #2
[Factory setting/value after clearing RAM: 0]
Reference:
Position #2 is an open space so floating dirt tends to be reflected on the images.
CCD-LUT Whether data is to be used for CCD gain compensation
This is used to compensate for the deterioration in the images (density differences in the center joins of the images) which
develops over time. Set whether or not to use the values adjusted by selecting COPIER>FUNCTION>CCD>LUT-
ADJ2.
Settings
0: Not used
1: Used
[Factory setting/value after clearing RAM: 0]
ITBB-TMG ITB cleaning band frequency setting
This changes the band image frequency. Lengthening the intervals enables the down time and toner consumption to be
reduced.
Settings
0 to 10 (in increments of 1: One banding per 100 sheets)
No banding at the "0" setting
[Factory setting/value after clearing RAM: 1]
FX-D-TMP Setting of threshold value for starting throughput reduction sequence when small size sheets are passed through
This sets the productivity reduction start temperature for sheets with widths less than A4R and sheets of an undefined
format. It improves the hot offset and productivity of sheets with widths less than A4R and sheets of an undefined format.
Settings
-4 to 4
[Factory setting/value after clearing RAM: 0]
FIX-ROT Threshold value setting of sub-thermistor temperature at which to end the racing after small size sheets have passed
through
This sets the large size job start temperature following the small size supporting fan-cooling. It improves the hot offset
or down time.
Settings
-2 to 2
[Factory setting/value after clearing RAM: 0]
FX-S-TMP ITOP temperature regulation offset adjustment
Adjustment of ITOP temperature for regular paper (64 to 105g paper) uniform speed
This reduces the unevenness in the gloss that appears for 94 mm at the leading edges of the sheets at the regular paper
uniform speed.
Settings
[Factory setting/value after clearing RAM: 0]
PAP-W-EN Density unevenness reduction mode during solid image output
This deals with cases where the left edges of solid images are darker or screw marks appear. Uneven density is reduced
by providing more space between the sheets so that the time during which the screw is rotated increases. Increase the
value when uneven density in the solid images becomes problematic. The time between sheets is increased by an amount
equivalent to the number of seconds set.
Setting
0 to 10 seconds
[Factory setting/value after clearing RAM: 0]
TMP-TBL2 Fixing temperature regulation temperature offset (thick paper)
Temperature adjustment of the temperature regulation for thick paper (106 to 163g paper)
This improves the hot offset or fixability of the thick paper (106 to 163g paper).
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
TMP-TBL3 Fixing temperature regulation temperature offset (super-thick paper)
Temperature adjustment of the temperature regulation for super-thick paper (164 to 220g paper)
This improves the hot offset or fixability of the super-thick paper (164 to 220g paper).
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
COPIER>OPTION>BODY
Chapter 17
1
1
1
1
1
1
1
1
1
1
1
17-49