Table of Contents
Advertisement
98
Selenio X100
Installation and Operation Manual
Enabling DTS Neural and Dolby Modes
Table 4-1.
Advanced Audio Processing Modes, Latency, MCPS, and Credit Cost
Mode
M1: UpMix (low/high latency)
M2: DownMix
M3: MultiMerge (low/high latency)
M4: Loudness Control 2.0
M5: Loudness Control 5.1
M6: Loudness Control 4x2.0
M7: Dolby Digital and Dolby Digital
Plus Decode with Downmix
M8: Dolby E Decode
M9: Dolby E, Dolby Digital, and
Dolby Digital Plus Decode with
Downmix
M10: Dolby Digital and Dolby Digital
Plus Encode
M11: Dolby E Encode
Follow these steps to enable the DTS Neural and Dolby Modes:
1
Consult
Table
4-1,
and then select either select Normal or Minimum at Misc > Other >
AAP Latency Mode.
The Minimum setting will reduce latency for AAP 1 and 3, but disable AAP 2 and 4.
Leave the setting at Normal if more than 2 AAPs are required.
2
Select one of the four slots in the Advanced Audio Processing (AAP) block.
3
Select the processing mode you need at General > Processing Mode.
4
In the drop down box at the top of the column, change your selection from General to the
mode you selected in step 3 (default is None).
5
Wait several seconds for the fields to refresh.
6
Configure the parameters that are available in your mode (parameters that are not
applicable are grayed out).
Once you have selected your DTS Neural modes, the Selection Status parameter
(AAP x > General) displays one of the following:
Good
Not Enough License Credit
Not Enough MCPS
Not Enough MCPS and License Credit
7
From the main section of the Advanced Audio Processing (AAP) block, (select AAP x
Input Routing and then select your audio sources.
8
In the Audio Output Routing and Delay block, select the destinations for your audio.
Normal Latency
64.2 ms (low) / 85.53
ms (high)
48.2 ms
64.2 ms (low) / 85.53
ms (high)
96.2 ms
96.2 ms
96.2 ms
66.58 ms
(DDD and DDPD)
2 frames
66.73 ms
144 ms
(DDE, DDPE 5.1/2.0;
DDPE 7.1/5.1 up to 7.1)
2 frames
MCPS,
Minimal
Normal
Latency
Latency *(%)
26.86 ms (low) /
38
48.19 ms (high)
10.86 ms
13
26.86 ms (low) /
50
48.19 ms (high)
58.86 ms
14
58.86 ms
25
58.86 ms
44
22 (DDD)
40.79 ms
(DDD and DDPD)
27 (DDPD)
2 frames
35
66.73 ms
35
44 (DD)
120 ms
(DDE, DDPE 5.1/2.0;
50
DDPE 7.1/5.1 up to
(DDPE 5.1/2.0
7.1)
80 (DDPE 7.1/
5.1 up to 7.1)
1.13 frames
46
Credit Cost
3 DTS
3 DTS
4 DTS
1 DTS
3 DTS
4 DTS
1 DDD (DDD
and DDPD)
1 DED*
1 (DED, DDPD,
DDD)
1 (DDE, DDPE)
1 DEE
Advertisement
Table of Contents
