Sharp AR-BC260 Service Manual page 153

3 -10
Purpose Operation test/check
Function Used to adjust the sections in the finisher.
(Purpose)
Section Finisher
Item Operation
Operation/ 1. Select the adjustment item with the scroll key.
Procedure 2. Enter the adjustment value with the 1o-key and
press the OK key to set the value.
Item
A Saddle binding position adjustment
B Saddle folding position adjustment
C Front alignment position adjustment
D Rear alignment position adjustment
E Staple rear one-point binding position
adjustment
F Staple front one-point binding position
adjustment
G Staple two-point binding center
adjustment
H Staple two-point binding pitch adjustment 0 – 100
I Punch center adjustment
J Punch hole position adjustment
4
4 -2
Purpose Operation test/check
Function Used to check the operations of the desk/large
(Purpose) capacity tray sensors and detectors and the related
circuits.
Section Paper feed
Item Operation
Operation/ The operating conditions of the sensors and
Procedure detectors in the paper feed section are displayed.
The active sensors and detectors are highlighted.
(Sensors to be detected)
DLUD1 Desk 1cs upper limit detection
DLUD2 Desk 2cs upper limit detection
DLUD3 Desk 3cs upper limit detection
DPED1 Desk 1cs paper empty detector
DPED2 Desk 2cs paper empty detection
DPED3 Desk 3cs paper empty detection
DCSPS1 Desk 1cs remaining quantity detection
DCSPS2 Desk 2cs remaining quantity detection
DCSPS3 Desk 3cs remaining quantity detection
DPPD1 Desk paper transport detection 1
DPPD2 Desk paper transport detection 2
DPPD3 Desk paper transport detection 3
DLUID1
DLUID2
DLUID3
DDOPD
DCSS11
DCSS12
DCSS13
DCSS14
DCSS21
DCSS22
DCSS23
DCSS24
DCSS31
DCSS32
DCSS33
DCSS34
LTD
LUD
Set Initial
LLD
range value
LPED
0 – 400 200
LTOD
0 – 400 200
LCD
0 – 20 10
LOSW
0 – 20 10
LRE
0 – 200 100
24V
LLSW
0 – 200 100
0 – 200 100
50
47 – 53 50
0 – 100 50
4 -3
Purpose
Function
(Purpose)
/
Section
Item
Operation/
Procedure
During the operation of the load, the [EXECUTE] key is
highlighted. If the [EXECUTE] key is pressed while it is
highlighted, the operation is stopped.
(Loads to be selected)
DM
DLM1
DLM2
DLM3
DPFC1
DPFC2
DPFC3
DTRC
DPFS1
DPFS2
DPFS3
LTM
LLM
LPFCL
LPSL
LTCL
LTLSL
AR-BC260 SIMULATION 9 - 15
Desk 1cs lift unit installation detection
Desk 2cs lift unit installation detection
Desk 3cs lift unit installation detection
Desk door open detection
Desk 1cs paper size detection 1
Desk 1cs paper size detection 2
Desk 1cs paper size detection 3
Desk 1cs paper size detection 4
Desk 2cs paper size detection 1
Desk 2cs paper size detection 2
Desk 2cs paper size detection 3
Desk 2cs paper size detection 4
Desk 3cs paper size detection 1
Desk 3cs paper size detection 2
Desk 3cs paper size detection 3
Desk 3cs paper size detection 4
Transport sensor
LCC upper limit detection
LCC lower limit detection
LCC paper empty detection
LCC main unit connection detection
LCC tray insertion detection
LCC upper open/close detection SW
LCC lift motor encoder
LCC24V detection
LCC upper limit SW
Operation test/check
Used to check the operations of the desk/large
capacity tray loads and the control circuit.
Paper feed
Operation
1. The names of the loads that can be checked are
displayed. Select a load to be checked with the
key, and the selected load is highlighted.
2. Press the [EXECUTE] key. The load selected in
procedure 1 starts the operation.
Desk transport motor
Desk 1cs lift-up motor
Desk 2cs lift-up motor
Desk 3cs lift-up motor
Desk 1cs paper feed clutch
Desk 2cs paper feed clutch
Desk 3cs paper feed clutch
Desk transport clutch
Desk 1cs paper feed solenoid
Desk 2cs paper feed solenoid
Desk 3cs paper feed solenoid
LCC transport motor
LCC lift motor operation
LCC paper feed clutch
LCC paper feed solenoid
LCC transport clutch
LCC tray lock solenoid