1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. AR-205
  6. Operation manual

Sharp AR-205 Operation Manual

Digital laser copier
Hide thumbs Also See for AR-205:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
MODEL
AR-205
DIGITAL LASER COPIER
OPERATION MANUAL
GETTING STARTED
MAKING COPIES
STATUS INDICATORS
GENERAL INFORMATION
OPTIONAL EQUIPMENT
APPENDIX
Page
2
13
29
39
57
77

Advertisement

Table of Contents
loading

Related Manuals for Sharp AR-205

Summary of Contents for Sharp AR-205

  • Page 1 MODEL AR-205 DIGITAL LASER COPIER OPERATION MANUAL Page GETTING STARTED MAKING COPIES STATUS INDICATORS GENERAL INFORMATION OPTIONAL EQUIPMENT APPENDIX...
  • Page 2 CAUTIONS Follow the cautions below when using this copier. The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. Place the copier on a firm, level surface. Do not install the copier in a humid or dusty location.

  • Page 3: Table Of Contents

    CONTENTS Page GETTING STARTED INTRODUCTION ....... . . 2 MAIN FEATURES ....... . 3 PART NAMES AND FUNCTIONS .

  • Page 4: Introduction

    INTRODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarise yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location.

  • Page 5: Main Features

    MAIN FEATURES High-speed laser copying First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). Copying speed is 20 copies/min., which adapts to business use, allowing improvement of working efficiency. High-quality digital image High-quality copying at 600 dpi is performed.

  • Page 6: Part Names And Functions

    PART NAMES AND FUNCTIONS Overall layout q Platen cover (optional) i Paper trays Place the original on the original table and close the Each tray holds 250 sheets of copy paper. platen cover before copying starts. o Side cover w Original table Open to remove misfeeds and to service the copier.
  • Page 7 PART NAMES AND FUNCTIONS !5 Drum cartridge handle @1 Fusing unit release levers Hold to pull out the drum cartridge. Lower to remove misfed paper. !6 Drum cartridge The fusing unit is hot. Copy images are formed on the photoconductive drum. Take care in removing paper.

  • Page 8: Operation Panel

    PART NAMES AND FUNCTIONS Operation panel Not used for the copier features. q INTERRUPT ( !3 B/W REVERSE ( ) key and indicator (p. 26) ) key and indicator (p. 24) Interrupts a copy run. Press to reverse the black and white areas. w Copy quantity display !4 XY-ZOOM ( ) key and indicator (p.
  • Page 9 PART NAMES AND FUNCTIONS Inch system In some countries and regions, 8-1/2" x 13" size is indicated on the operation panel. 1st display 2nd display The general location of misfed paper is shown by a blinking red indicator ( #1 DUAL PAGE COPY ( ) key and indicator (p.

  • Page 10: Copier Installation

    COPIER INSTALLATION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions.

  • Page 11: Cautions On Handling

    CAUTIONS ON HANDLING Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum cartridge, causing poor copy quality.

  • Page 12: Loading Copy Paper

    To save space, this copier has been designed with adjustable front-loading trays, which are easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 52.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.

  • Page 13: Loading Copy Paper

    LOADING COPY PAPER Changing the copy paper size in the tray Gently lift and pull out the paper tray until it stops. Push the pressure plate down until it locks in place. Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper.
  • Page 14 LOADING COPY PAPER To set the selected paper size, press the PAPER SIZE ENTER ( ) key. The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily. All other indicators will go out. For paper size setting, ensure that the COPY mode has been selected.

  • Page 15: Auditing Accounts

    AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 42 for setting the auditing mode. If the copier has been programmed in the auditing mode, “– – –” will appear in the copy quantity display in the initial conditions.

  • Page 16: Normal Copying

    NORMAL COPYING Turn the power switch on. It will take about 35 seconds for the copier to warm up. However, you Power on can make desired settings and press the START ( ) key during warm-up. Copying will start after warm-up. If the copier has been programmed in the auditing mode, the START key ( ) indicator will not light up and “–...

  • Page 17: Normal Copying

    NORMAL COPYING For manual copy density adjustment, press the AUTO/MANUAL/ PHOTO ( ) key to select MANUAL ( ) and adjust with the light ( ) and dark ( ) keys as desired. For photographs, select PHOTO ( ) and then adjust with the light ) and dark ( ) keys as desired.

  • Page 18: Reduction/Enlargement/Zoom

    REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE ( ) key or manually with the PRESET RATIO selector ( ) keys and/or the zoom ( ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. Automatic Place the original on the original table and close the platen cover.
  • Page 19 REDUCTION/ENLARGEMENT/ZOOM Manual Place the original on the original table and close the platen cover. Use the PRESET RATIO selector ( ) keys and the zoom ( ) keys to select the desired copy ratio. To select a preset reduction or enlargement copy ratio, press the key repeatedly until the indicator for the desired copy ratio is lit.

  • Page 20: Bypass Feed (Special Paper)

    BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying.
  • Page 21 BYPASS FEED (special paper) Press the TRAY SELECT ( ) key to select the bypass tray. Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes. Press the START ( ) key.

  • Page 22: Two-Sided Copying

    TWO-SIDED COPYING Automatic two-sided copying can be made with this copier. For two-sided copying from the original table, follow the procedure below. Fully automatic two-sided copies can be made from one-sided originals if either an optional single pass feeder (SPF) or an optional reversing single pass feeder (RSPF) is installed.
  • Page 23 TWO-SIDED COPYING Place the second original face down on the original table and press the START ( ) key again to copy onto the other side. To stop a copy run during duplex copying, press the CLEAR ( ) key. To cancel the duplex mode, press the ORIGINAL TO COPY key until the indicators in the ORIGINAL TO COPY section all go out.

  • Page 24: Xy Zoom

    XY ZOOM The XY ZOOM feature allows the horizontal and vertical copy ratios to be Original Copy changed independently. This feature cannot be used with the 2 in 1 or 4 in 1 feature. (The 2 in 1 or 4 in 1 feature can only be used when an optional electronic sorting kit and an optional SPF or RSPF are installed.) To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature.
  • Page 25 XY ZOOM Use the PRESET RATIO selector ( ) keys and zoom ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction. Press the copy ratio display ( ) key. The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display.

  • Page 26: B/W Reverse

    B/W REVERSE Original Copy The B/W REVERSE feature is used to reverse black and white areas. When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected. Even if this feature is cancelled, the MANUAL mode will not auto- matically be cancelled.

  • Page 27: Dual Page Copy

    DUAL PAGE COPY Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. This feature cannot be used with the 2 in 1 or 4 in 1 feature and sort/group feature.

  • Page 28: Interrupting A Copy Run

    INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. Sort or group cannot be selected during interrupt copying. (Sort and group can be performed only if an optional electronic sortring kit and an optional SPF or RSPF are installed.) INTERRUPT will not function during two-sided copying.

  • Page 29: Automatic Exposure Adjustment

    AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the optional SPF or RSPF respectively. To set the level for the optional SPF or RSPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1.

  • Page 30: Toner Save Mode

    TONER SAVE MODE This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the PHOTO mode. Follow the procedure below for setting the toning level. Press the AUTO/MANUAL/PHOTO ( ) key to select the MANUAL (...

  • Page 31: Td Cartridge Replacement

    SHARP products. cartridge replacement required ( ) indicator will blink and the START key The package of SHARP toner has the Genuine ) indicator will go out. When sufficient toner has been added, the Supplies label. blinking indicator will go out and the START key indicator will light up indicating that copying can be resumed.

  • Page 32: Td Cartridge Replacement

    TD CARTRIDGE REPLACEMENT Remove the protective cover from the TD cartridge by unlatching three cover hooks from the holes on the cartridge and then pulling the cover in the direction indicated by the arrow in the illustration. Gently insert the TD cartridge along the guides until it locks in place.

  • Page 33: Drum Cartridge Replacement

    SHARP products. replacement required ( ) indicator will light up indicating that replacement The package of the SHARP drum cartridge has of the drum cartridge will be needed soon. When the indicator begins to blink, the Genuine Supplies label. replace the drum cartridge by following the procedure given below.
  • Page 34 DRUM CARTRIDGE REPLACEMENT Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides. Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies.

  • Page 35: Misfeed Removal

    MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed If paper is accidentally torn during removal, be sure to ) indicator will blink, and blinking red misfeed location remove all pieces. indicators will indicate the approximate misfeed location. Be careful not to damage the photoconductive drum.
  • Page 36 MISFEED REMOVAL Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to “B. Misfeed in the fusing area”. If the misfed paper is seen from this side, proceed to “C.
  • Page 37 MISFEED REMOVAL Turn the roller rotating knob in the direction of the Roller rotating knob arrow. Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. Fusing unit release lever The fusing unit is hot.
  • Page 38 MISFEED REMOVAL Close the side cover by pressing the handle on the cover. The misfeed ( ) indicator will go out. Misfeed in the upper paper tray Before opening the upper paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A.
  • Page 39 MISFEED REMOVAL Misfeed in the lower paper tray Grasp the handle of the lower side cover and gently open the cover. Remove the misfed paper. Be careful not to tear the misfed paper during removal. If the misfed paper is not seen in step 2, gently lift and pull out the lower paper tray and remove the misfed paper.

  • Page 40: Maintenance Required

    MAINTENANCE REQUIRED When the indicator lights up, service by an authorised SHARP service technician is required. Contact your service centre as soon as possible.

  • Page 41: User Programs

    USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. List of user programs This copier has the following user programs. Program No. Program name Description Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.

  • Page 42: User Programs

    USER PROGRAMS Setting the user programs Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , and blink and “– –” appears in the copy quantity display. Enter a program number using the numeric keys. The selected program number will blink in the copy quantity display.
  • Page 43 USER PROGRAMS Select the desired parameter using the numeric keys. The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2.

  • Page 44: Settings For Auditing Accounts

    USER PROGRAMS Settings for auditing accounts Setting of user programs No. 10 to 15 varies with the program number. For settings of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 39 to select a program. (1. Press the light ( ) key for more than 5 seconds.
  • Page 45 USER PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. If no account number has been registered, “12E” will appear in the copy quantity display.
  • Page 46 USER PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. If no account number has been registered, “14E”...
  • Page 47 USER PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. If no account number has been registered, “15E”...

  • Page 48: Power Save Modes

    POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec.* for preheat mode and 30 min.

  • Page 49: Power Save Modes

    POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode.

  • Page 50: User Maintenance

    USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and platen cover Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth.

  • Page 51: Copier Trouble

    COPIER TROUBLE? Problem Solution Copier plugged in? Plug the copier into a grounded outlet. See page 8. Copier does not operate. Power switch ON? Turn the power switch ON. See page 14. Copy density properly adjusted? See pages 14 and 27. Copies are too dark or too light.
  • Page 52 Copies are smudged or dirty. Original smudged or blotchy? Use a clean original. Maintenance is required. Contact your SHARP Is the indicator on? service centre as soon as possible. Is the COPY indicator off? Use the COPY/FAX key to select the COPY mode.
  • Page 53 Be sure to use only genuine SHARP parts and supplies. Please contact your SHARP service centre immediately if a problem persists after checking the above. Self-diagnostic function An automatic self-diagnostic function is built into the copier.

  • Page 54: Supplies

    These will cause physical damage to the copier. For best results, use only paper recommended by SHARP. Special papers except envelopes must be fed one sheet at a time through the bypass tray. Up to 10 envelopes can be set at one time.

  • Page 55: Genuine Supplies Statement

    For best copying results, be sure to use only Standard supplies for this copier that are to be replaced by the user are copy SHARP products. paper, TD cartridge, and drum cartridge. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES Proper storage...

  • Page 56: Specifications

    SPECIFICATIONS Type Digital laser copier, desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 (11" x 17") Copy sizes Max. A3 (11" x 17") Min. A6 (5-1/2" x 8-1/2") Image loss: Max. 4 mm (5/32") (leading and trailing edges) Max.
  • Page 57 Some options may not be available in some countries. As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.
  • Page 58 MEMO...

  • Page 59: Optional Equipment

    OPTIONAL EQUIPMENT CONTENTS Page SYSTEM CONFIGURATION ......58 SINGLE PASS FEEDER (AR-SP2)/ REVERSING SINGLE PASS FEEDER (AR-RP1) ... 59 Part names .

  • Page 60: System Configuration

    SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following. Single pass feeder Reversing single pass feeder (AR-SP2) (AR-RP1) Platen cover (AR-VR1) Electronic sorting kit (AR-EB3) Facsimile expansion kit (AR-FX2)* Printer expansion kit (AR-PB8)*...

  • Page 61: Single Pass Feeder (Ar-Sp2)/ Reversing Single Pass Feeder (Ar-Rp1)

    583 mm (W) x 435 mm (D) x 131 mm (H) (22-61/64" (W) x 17-1/8" (D) x 5-5/32" (H)) As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice.

  • Page 62: Using The Spf Or The Rspf

    SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Using the SPF or RSPF Be sure to remove any staples or paper clips from the Special originals such as transparency film and tracing originals. paper should not be fed through the SPF or RSPF but Damaged or crumpled originals may misfeed in the SPF should be copied from the original table.
  • Page 63 SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Set the number of copies and press the START ( ) key. Press the CLEAR ( ) key to stop copying in the middle of a run. Two-sided copies from One-sided originals Ensure that no original is left on the original table.
  • Page 64 SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Press the START ( ) key. For two-sided copying, a multiple number of copies can only be set if an optional electronic sorting kit is installed. Two-sided copies from two-sided originals To copy in the two-sided to two-sided copy mode, an optional reversing single pass feeder (AR-RP1) must be installed.
  • Page 65 SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Press the START ( ) key. For two-sided copying, a multiple number of copies can only be set if an optional electronic sorting kit is installed. Be sure not to touch the originals as they move on the reversing tray. This may cause misfeeds.

  • Page 66: Setting Image Rotation In Duplex Copying

    SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Setting image rotation in duplex copying Press and hold down the ORIGINAL TO COPY key for approximately 5 seconds until the indicator will blink and the currently selected parameter number will blink in the copy quantity display.

  • Page 67: Misfeed Removal

    SINGLE PASS FEEDER ( AR-SP2 )/REVERSING SINGLE PASS FEEDER (AR-RP1) Misfeed removal If an original misfeed occurs in the SPF or RSPF, the copier will stop and the red indicator which indicates an original misfeed will blink. Location A Open the feeding roller cover and pull the original gently Feeding roller cover to the left and out from the document feeder tray.

  • Page 68: Electronic Sorting Kit (Ar-Eb3)

    The memory can be expanded by adding commercially available memories recommended by SHARP. For details, contact your dealer. To use the 2 in 1 or 4 in 1 and sort/group functions, an optional single pass feeder (AR-SP2) or reversing single pass feeder (AR-RP1) is needed.

  • Page 69: Sort/Group

    ELECTRONIC SORTING KIT (AR-EB3) Sort/group If an optional electronic sorting kit is installed, the copier will have two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature.
  • Page 70 ELECTRONIC SORTING KIT (AR-EB3) Copying in the sort mode When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. To copy in the sort mode, an optional single pass feeder (AR-SP2) or reversing single pass feeder (AR-RP1) is needed.

  • Page 71: In 1 Or 4 In 1

    ELECTRONIC SORTING KIT (AR-EB3) 2 in 1 or 4 in 1 The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a 2 in 1 copying specified order, onto one sheet. To use these features, an optional single pass feeder (AR-SP2) or reversing single pass feeder (AR-RP1) is needed.
  • Page 72 ELECTRONIC SORTING KIT (AR-EB3) Enter the desired pattern number using a numeric key. The entered number will blink in the copy quantity display. For layout pattern numbers, see the previous page. Press the START ( ) key. The entered number will light up steadily. Press the 2 IN 1 / 4 IN 1 ( ) key to complete the selection.

  • Page 73: Erase

    ELECTRONIC SORTING KIT (AR-EB3) Erase This copier has an edge erase mode and a centre erase mode. Edge erase Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. Centre erase can be used to eliminate the shadow produced by the bindings of bound documents.
  • Page 74 ELECTRONIC SORTING KIT (AR-EB3) Set the number of copies. Press the START ( ) key.

  • Page 75: Margin Shift

    ELECTRONIC SORTING KIT (AR-EB3) Margin shift The MARGIN SHIFT feature automatically shifts the text or image to Original Copy increase the margin by approximately 9 mm (1/4") . The location of the margin to be increased can be selected to be either at the left edge or the top of the page.

  • Page 76: 250-Sheet Paper Feed Unit (Ar-De5) 2X250-Sheet Paper Feed Unit (Ar-De6)

    250-SHEET PAPER FEED UNIT (AR-DE5) 2x250-SHEET PAPER FEED UNIT (AR-DE6) These paper feed units provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. The AR-DE5 contains one 250-sheet paper tray and the AR-DE6 contains two 250-sheet paper trays.
  • Page 77 250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( ) indicator and the red indicator which indicates the paper feed unit will blink. Open the side cover of the paper feed unit and remove the misfed paper.
  • Page 78 (23-15/64" (W) x 18-35/64" (D) x 6-27/32" (H)) Power supply Drawn from the copier As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.

  • Page 79: Transfer Charger Cleaning

    TRANSFER CHARGER CLEANING If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. Turn the power switch off. Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. Gently lift and pull out the upper paper tray and take the Charger cleaner charger cleaner out by holding the tab.

  • Page 80: Drum Cartridge Life

    DRUM CARTRIDGE LIFE To find out how many more copies can be made before the 30,000 mark is reached, follow the procedure described below. Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( ) blink and “–...

  • Page 81: Index

    INDEX 250-sheet paper feed unit ..... . . 74 Group ........67 2 in 1 .
  • Page 82 INDEX Reduction ........16 Replacement – drum cartridge ......31 –...

  • Page 83: Material Safety Data Sheet

    (Name and Telephone Number) U.S.A. Sharp Electronics Corporation Telephone number for information: 1-800-237-4277 Emergency telephone number: 1-800-255-3924 Canada Sharp Electronics of Canada Ltd. Telephone number for information: 905-890-2100 Emergency telephone number: 1-800-255-3924 United Kingdom Sharp Electronics (U.K.) Ltd. Telephone number for information: 01923-474013 Section 3.
  • Page 84 Section 6. Physical Chemical Characteristics Boiling / Melting Point: Not applicable Specific Gravity: Vapor Pressure: Not applicable Solubility in Water: Negligible Vapor Density: Not applicable Not applicable Evaporation Rate: Not applicable Viscosity: Not applicable Appearance: Fine powder Color: Black Odor: Odorless Section 7.
  • Page 85 (Name and Telephone Number) U.S.A. Sharp Electronics Corporation Telephone number for information: 1-800-237-4277 Emergency telephone number: 1-800-255-3924 Canada Sharp Electronics of Canada Ltd. Telephone number for information: 905-890-2100 Emergency telephone number: 1-800-255-3924 United Kingdom Sharp Electronics (U.K.) Ltd. Telephone number for information: 01923-474013 Section 3.
  • Page 86 Section 6. Physical Chemical Characteristics Boiling / Melting Point: Not applicable Specific Gravity: about 7.3 Vapor Pressure: Not applicable Solubility in Water: Negligible Vapor Density: Not applicable Not applicable Evaporation Rate: Not applicable Viscosity: Not applicable Appearance: Fine powder Color: Black Odor: Odorless...
  • Page 87 MEMO...
  • Page 88 MEMO...
  • Page 89 MEMO...
  • Page 90 Warning! This product is a class A product. If it is operated in households, offices or similar surroundings, it can produce radio interferences at other appliances, so that the user has to take adequate countermeasures. VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN...
  • Page 91 In some areas, the “POWER” switch positions are marked “I ” and “ ” on the copier instead of “ON” and “OFF”. The symbol “ ” denotes the copier is not completely de-energized but in a stand-by condition at this “POWER” switch position. If your copier is so marked, please read “I ”...

  • Page 92: Sharp Corporation

    AR-205 SHARP CORPORATION PRINTED IN HONG KONG TINSE0194QSZZ...

Table of Contents