Xconfiguration Experimental Ctmssupport Mode; Xconfiguration Experimental Customsoftbuttons State [1..2] Softbutton [1..5] Type; Xconfiguration Experimental Enable1080P60; Xconfiguration Experimental Networkservices Upnp Mode - Cisco TelePresence System Codec C90 Reference Manual

Cisco TelePresence System Codec C90
Contents Introduction

xConfiguration Experimental CustomSoftbuttons State [1..2] Softbutton [1..5] Type

NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <NotSet/MainSource/PresentationSource/CameraPreset/Actions/
SpeedDial>
Example: xConfiguration Experimental CustomSoftbuttons State 1 Softbutton 1
Type: NotSet
xConfiguration Experimental CustomSoftbuttons State [1..2] Softbutton [1..5] Value
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
ADMIN
Requires user role:
<S: 0, 255>
Value space:
Example: xConfiguration Experimental CustomSoftbuttons State 1 Softbutton 1
Value: ""

xConfiguration Experimental Enable1080p60

NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
<On/Off>
Value space:
xConfiguration Experimental Enable1080p60: Off
Example:

xConfiguration Experimental NetworkServices UPnP Mode

NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <On/Off>
Example: xConfiguration Experimental NetworkServices UPnP Mode: Off

xConfiguration Experimental NetworkServices UPnP Timeout

NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <0..3600>
Example: xConfiguration Experimental NetworkServices UPnP Timeout: 0
D14641.06 Codec C90 API Reference Guide TC5.0 November 2011.
© 2010-2011 Cisco Systems, Inc. All rights reserved.
About the API xConfiguration xConfiguration

xConfiguration Experimental CTMSSupport Mode

xConfiguration Experimental PacketOverloadHandling WhenDetected

xConfiguration Experimental SystemUnit MenuType

xConfiguration Experimental SystemUnit SoftwareUpgrade RequireAuthentication

68
xCommand
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
This configuration tells whether CTMS (Cisco TelePresence Multipoint Switch) is supported or not.
Requires user role: ADMIN
Value space: <Off/On>
Off: CTMS is not supported.
On: CTMS is supported.
xConfiguration Experimental CTMSSupport Mode: On
Example:
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <Off/CallRate2256/CallRate768/ReduceTo576p/ReduceTo360p/Unencrypted/
Disconnect>
Example: xConfiguration Experimental PacketOverloadHandling WhenDetected: Off
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <Indicators/Full>
Example: xConfiguration Experimental SystemUnit MenuType: Full
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <On/Off>
Example: xConfiguration Experimental SystemUnit SoftwareUpgrade
RequireAuthentication: Off
API Reference Guide
xStatus Appendices
www.cisco.com