Setting The Trigger Out; Zone2 And Zone3 Tone Control And Channel Level Setting - Denon AVC-A11XV Operating Instructions Manual

ENGLISH
Advanced Setup – Part 1

Setting the Trigger Out

• Three 12 V DC Trigger Outputs on the rear panel can
be used to control other devices with compatible
trigger inputs, such as motorized screens, motorized
screen masking, motorized drapes, and other trigger-
controlled devices.
• Set the DC output supplied from the trigger out
terminals for the various input sources to "ON" or
"OFF".
1
CURSOR D D H H
Press the or
select the "Trigger Out" at the "Option
Setup" menu, then press the
button.
• Display the "Trigger Out" screen.
2
CURSOR D D H H
Press the or
select the trigger out terminal you want
ENTER
to set, then press the button.
• Switch to the setting screen.
Example:
When "Trigger Out 1" is selected
3 CURSOR F F G G
Press the or
select the zone (MAIN ZONE, ZONE2
and ZONE3).
The power supplied from the trigger out terminal
turns on and off when the power for the set zone
is turned on and off.
4
CURSOR D D H H
Press the or
select the input source, then press the
CURSOR F F G G
or button to select the
"ON" or "OFF".
ON:
When that input source is selected, the power
supplied from the trigger out terminal turns on.
OFF:
When that input source is selected, the power
supplied from the trigger out terminal turns off.
5
If "MAIN" was selected at step 3:
CURSOR D D
Press the
select the surround mode, then press the
button to
CURSOR F F G G
or button to select the
ENTER "ON" or "OFF".
ON:
If that surround mode is selected when an input
source set to "ON" is selected, the power
supplied from the trigger out terminal turns on.
OFF:
If that surround mode is selected when an input
source set to "ON" is selected, the power
supplied from the trigger out terminal turns off.
button to
6
ENTER
Press the button.
• Return to the "Trigger Out" screen.
Use the same procedure to make the settings for
Trigger Out 2, 3.
7
CURSOR D D
Press the
select the "Exit", then press the
button to button.
• The "Option Setup" menu reappears.
button to
If "Yes" is selected for "Default", the setting are
automatically reset to the default values.
ZONE2 and ZONE3 tone control and
channel level setting
Adjust the sound output from ZONE2 and ZONE3.
1
CURSOR D D
Press the
select the "Zone2/3 Tone/Ch Lev." at the
"Option Setup" menu, then press the
ENTER
button.
H H
or button to • Display the "Zone2/3 Tone/Ch Lev." screen.
2
CURSOR D D
Press the
select the zone whose sound you want to
adjust (ZONE2, ZONE3), then press the
ENTER
button.
• Switch to the setting screen.
Example:
When "Zone2" is selected
H H
or button to
ENTER
51
ENGLISH
Advanced Setup – Part 1
3 CURSOR D D
Press the
select the item to be set, then press the
CURSOR F F
or
parameter.
H H
or button to Bass:
Adjust the tone for the bass.
Treble:
Adjust the tone for the treble. (The bass or treble
sound can be adjusted between –12 dB and +12
dB in steps of 2.0 dB.)
HPF:
Set this to "ON" if your speakers do not have a
very strong capacity for producing low bass. Using
the high pass filter makes it possible to reduce
distortion of the bass sound.
Channel Level:
Set so that the playback level is the same for the
H H
or button to left and right channels. (The volume can adjusted
between –12 dB and +12 dB in steps of 1.0 dB.)
4
ENTER
Press the
• Return to the "Zone2/3 Tone/Ch Lev."
screen.
Use the same procedure to make the settings for
ZONE3.
5 CURSOR D D
Press the
select the "Exit", then press the
button.
• The "Option Setup" menu reappears.
• The "Channel Level" setting is only possible when
ZONE2 or ZONE3 is set to Stereo in the "Channel
Setup" menu.
H H
or button to
G G
button to adjust the
button.
H H
or button to
ENTER