Check Of The Measurement Result; About The Error Message; Playing A Dvd With Surround Sound - Denon AVC-A11XV Operating Instructions Manual

ENGLISH
Easy Setup and Operation

Check of the measurement result

The results of the measured items can be checked.
1 CURSOR D D H H
Press the or
select the items, then press the
button.
• Switch to the verification screen.
Example: Speaker Config. Check
[ First screen ]
2
ENTER
Press the button.
• Switch to the second screen.
Example: Speaker Config. Check
[ Second screen ]
3
If the check ends, press the
button again.
4
CURSOR D D H H
Press the or
select whether or not to save the data
you have checked.
Store:
Set with the checked measurement value.
All parameters are stored up.
Cancel:
Cancel the auto setup settings.
5
CURSOR F F
Press the
• After the data is stored, the "Auto Setup /
Room EQ" menu
automatically.
button to
ENTER
• Sometimes due to the electrical complexities of
subwoofers and the interaction with the room, THX
recommends setting the level and the distance of
the subwoofer manually.
• Sometimes due to interaction with the room, you
may notice irregular results when setting the level
and/or distance of the main speakers. If this
happens, THX recommends setting them manually.
• Please note that any THX main speakers should be
set to Small (80 Hz). If you set up your speakers
using Auto Setup, please make sure manually that
any THX speakers are set to Small with 80 Hz
crossover.
• When measurements have been made using the
measurement microphone, speakers with a built-in
filter such as subwoofers might be set with a value
that differs from the physical distance because of
the internal electrical delay.
NOTE:
• Do not turn off the power while the data is being
stored. If the power is turned off while the data
is being stored, the Room EQ parameters stored
ENTER
in the memory will be cleared, and it will not be
possible to select the "Audyssey", "Front" or
"Flat" equalizer settings.
button to

About the error message

These error messages will be displayed when
performing the measurements of Auto Setup and the
automatic measurements can not be completed
because of the speaker arrangement, measurement
environment, or other factors. Please check the
following matters, reset the pertinent items, and
measure again. Be sure to turn off the AVC-A11XV's
power before checking the speaker connections.
Screen example
button.
screen appears

Playing a DVD with surround sound

1
Disconnect the microphone from the
unit.
2
Select the input source to be played.
3
Select the play mode.
11
ENGLISH
Easy Setup and Operation
Cause
q The speakers required for producing • Check that the pertinent speakers
suitable reproduction have not been
detected.
• The front L and front R speakers were not
properly detected.
• Only one channel of the surround (A) and
surround (B) speakers was detected.
• Sound was output from the R channel
when only one surround back speaker was
connected.
• The surround back or the surround (B)
speaker was detected, but the surround
(A) speaker was not detected.
If multiple errors occur, press the CURSOR
F F or G G button to check the contents.
w The speaker polarity is connected in • Check
reverse.
• For some speakers, the screen
If multiple errors occur, press the CURSOR
F F or G G button to check the contents.
e There is too much ambient noise in the
• Either turn off the power of the
room and the measurements cannot be
made accurately.
• Try again at a time when it is
r The sound level that is output from the • Check
speakers and/or subwoofer is too low.
• Adjust the subwoofer's output
t The measurement microphone is not • Connect
connected, or all of speakers have not
been detected.
• Check the speaker connection.
4
Start DVD playback.
5
Adjust the volume.
Measures
are properly connected.
the polarity of the
pertinent speakers.
below may be displayed even
though the speakers are properly
connected.
If so, select "Skip ".
0
device that generated the noise
during the measurements or
move the device away.
quieter.
the placement and
orientation of the loudspeakers.
level.
the measurement
microphone to the microphone
connector.