Setting The Ieee1394 Auto Function; Video Setup; Setting The Hdmi/Dvi In Assign - Denon AVC-A11XV Operating Instructions Manual

Advanced Setup – Part 1
• If you do not wish to assign the device connected by
IEEE1394 cable to an input source, the IEEE1394
input can be selected by turning the FUNCTION knob.
In this case, the connection information is cleared
when the power of the connected device or the AVC-
A11XV is turned off, so the selection procedure must
be performed again.
• By default, if no device has been connected using an
IEEE1394 cable in the past, "No Connection" is
displayed.
• "Connection Change" is displayed if there is a
change in the IEEE1394 connection status while this
screen is displayed.
• If the model name cannot be acquired from the
connected IEEE1394 device, "UNKNOWN" is
displayed.
• If an IEEE1394 device other than one for IEEE1394
audio playback is connected, "Not Play" is displayed
and the input source cannot be assigned.

Setting the IEEE1394 Auto Function

Set whether or not to automatically play the IEEE1394
device when it is selected with the FUNCTION knob.
1 CURSOR D D H H
Press the or button to
select the "IEEE1394 Auto Func." at the
"Audio Input Setup" menu, then press
ENTER
the button.
• Display the "IEEE1394 Auto Func." screen.
2
CURSOR F F G G
Press the or button to
select the "ON" or "OFF".
ON:
Select this to automatically play the device.
OFF:
Select this if you do not want to automatically play
the device.
In some cases settings may be required on your
player. Also refer to the player's operating
instructions.
3
ENTER
Press the button to enter the
setting.
• The "Audio Input Setup" menu reappears.
4
CURSOR D D H H
Press the or button to
ENTER
select the "Exit", then press the
button.
• The "System Setup Menu" reappears.
Video Setups
Make the video-related settings.
Setting the HDMI / DVI In Assign
• This setting assigns the HDMI input terminals and
DVI input terminal for different input sources.
• Set the method for playing the audio signals included
in the HDMI input signal.
1
CURSOR D D H H
Press the or
select the "Video Setup" at the "System
Setup Menu", then press the
button.
• Display the "Video Setup" menu screen.
2
CURSOR D D H H
Press the or
select the "HDMI / DVI In Assign" at
the "Video Setup" menu, then press the
ENTER
button.
• Display the "HDMI / DVI In Assign" screen.
3
CURSOR D D H H
Press the or
select the input source, then press the
CURSOR F F G G
or button to select the
input terminal.
Select from among HDMI1 to 3 and DVI-D.
If the same HDMI or DVI input terminal is
selected, the setting for the input source that
was previously assigned switches to "NONE".
44
ENGLISH
Advanced Setup – Part 1
4
CURSOR D D
Press the
select the method for playing the audio
signals included in the HDMI input
signal, then press the
button to select the "TV" or "AMP".
button to
TV:
Play the audio signals on a monitor TV connected
ENTER
to the AVC-A11XV.
AMP:
Play the audio signals on speakers connected to
the AVC-A11XV.
button to
5
CURSOR D D
Press the
select the input for the playback of
signals when the audio signal of HDMI
can not be reproduced, then press the
CURSOR F F G G
or button to select the
input signal (ANALOG or EXT. IN).
button to
When the audio signal of HDMI has become
unlocked, the unit automatically changes over to
the set connector (ANALOG or EXT. IN).
1 ~ 3 correspond to each HDMI 1 ~ 3 input
terminal.
6 ENTER
Press the button to enter the
setting.
• The "Video Setup" menu reappears.
ENGLISH
H H
or button to
CURSOR F F G G
or
H H
or button to