System Call; Punch Through; Setting The Back Light's Lighting Time; Setting The Brightness - Denon AVC-A11XV Operating Instructions Manual

Advanced Operation
2 Storing system call signals
1
ON OFF
Press the and button at the
same time.
2
3
Press the button to select system call
setting.
3
MODE SELECTOR
Press the button for
the component you want to register at

SYSTEM CALL

the button, then press
ENTER
the button.
4
Press the button you want to register.
The mode can be switched by pressing a MODE
SELECTOR button.
5
Repeat steps 4 to register the desired
buttons.
Up to 12 signals each can be stored at the
SYSTEM CALL 1 ~ 6.
6
ENTER
Press the button after the button
registration is completed.
• There will be a changeover to the system call
registration screen.
7
SYSTEM CALL 1
Press buttons from
6
to register the system call.
• "OK" is displayed and the set returns to the
normal operating mode.
• If you exceed the number of signals that can be
registered, there will be a changeover to the system
call registration screen.
NOTE:
• The remote control signals of the buttons
pressed while registering the system call signals
are emitted, so be careful not to operate the
components accidentally (cover the remote
sensors, for example).
2 Using the system call function
Press the button at which the system call
signals have been stored.
• The stored signals are transmitted successively.

Punch through

Buttons used in the CD, CDR, DVD, DVDR, VDP,
VCR1 and VCR2 modes can be assigned to the
buttons which are not normally used in the AMP,
ZONE2, ZONE3, ZONE4, TV and DBS modes.
For example, when the CD mode is set to the punch
through mode in the AMP mode, the CD mode's PLAY,
STOP, MANUAL SEARCH, AUTO SEARCH and PAUSE
buttons' signals are sent in the AMP mode. (
1
ON OFF
Press the and button at the
same time.
2
4
Press the button to select punch
through setting.
3
MODE SELECTOR
Press the button for
the component you want to make the
punch through setting, then press the
ENTER
button.
to
4
MODE SELECTOR
Press the button for
the component you want to punch
ENTER
through, then press the
• The punch through is set and the set returns
to the normal operating mode.

Setting the back light's lighting time

1
ON OFF
Press the and
same time.
2
5
Press the button to select Light setup.
3
Press the button you want to adjust the
lighting time (5 sec ~ 20 sec).
2 Lighting time
1 : 5 sec
2 : 10 sec (factory default)
3 : 15 sec
4 : 20 sec
)

Setting the brightness

The brightness of the display can be adjusted in 3
levels.
2 For 1 brightness step increase
ENTER
Hold the button and press the
CHANNEL +
button.
2 For 1 brightness step decrease
button.
ENTER
Hold the button and press the
CHANNEL –
button.
36
ENGLISH

Resetting

2 Resetting the preset memory
button at the
1
ON
Press the and
same time.
2
6
Press the button to select resetting.
3
1
Press the button to resetting the preset
memory.
2 Resetting List
1 : Resetting the preset memory
2 : Resetting the "Learned" buttons
3 : Resetting the system call
4 : Resetting the punch through setting
+10 : All reset function (factory default)
• The MODE SELECTOR buttons that were set in
preset memory will all light.
4 MODE SELECTOR
Press the
want to resetting, then press the
button.
• The set returns to the normal operating
mode.
2 Resetting the learned buttons
1
ON
Press the and
same time.
2
6
Press the button to select resetting.
3
2
Press the button to resetting the
learned buttons.
• The MODE SELECTOR buttons will all light.
4
MODE SELECTOR
Press the
want to resetting, then press the
button.
• The set returns to the normal operating
mode.
ENGLISH
Advanced Operation
OFF
button at the
button you
ENTER
OFF
button at the
button you
ENTER