Trigger Out 1; Trigger Out 2; A0 Trigger Out 3; A1 Trigger Out 4 - Denon AVP-A1HD Owner's Manual

k Trigger Out 1
Select the conditions to turn on the trigger out 1 with respect to
the zone, input source, surround mode, HDMI monitor, etc.
For details about the trigger out function, see page 22.
l Trigger Out 2
This sets the conditions to turn on the trigger out 2, in the same
way as "Trigger Out 1" above.
A0 Trigger Out 3
This sets the conditions to turn on the trigger out 3, in the same
way as "Trigger Out 1" above.
A1 Trigger Out 4
This sets the conditions to turn on the trigger out 4, in the same
way as "Trigger Out 1" above.
ON – – –
[Selectable items]
Setting with Respect to the Zone
When the power of the zone turned on/off, the trigger out turns on.
Setting with Respect to the Input Source
When the input source set to on is selected, the trigger out turns on.
Associated with respect to the input source for zones set to "ON" at
"Setting with Respect to the Zone" .
Setting with Respect to the Surround Mode
When the surround mode set to on is selected, the trigger out turns
on.
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the "Setting with Respect to the
Input Source" .
0
Setting with Respect to the Monitor
When the HDMI monitor set to on is selected, the trigger out turns
on.
This is effective when the "MAIN ZONE" has been set to "ON" for
the "Setting with Respect to the Zone" and the input source which is
set to "ON" has been selected for the "Setting with Respect to the
Input Source" .
A2 Transducer Setup
Set when using transducer.
The Transducer Setup can be accessed through GUI menu "Speaker
Setup" - "Subwoofer Setup" is "1SP" , "2SP L/R" or "2SP MIX" . The
transducer signal is outputted from "SW3" .
Level
[Variable range]
–12dB ~ ~ +12dB
0dB
:
Set the transducer level.
OFF
:
Turn the transducer output off.
When you adjust "Level" , the adjusted value is set for all surround
modes. To adjust the level for individual surround modes, use "Channel
Level" (vpage 65).
LPF
Set the upper limit of the low frequency output to the transducer.
[Selectable items]
40Hz 60Hz 80Hz 90Hz 100Hz
150Hz 200Hz 250Hz
A3 Digital Out
Set usage of OPT4 OUT.
[Selectable items] ZONE4 Select Rec Select
NOTE
The ZONE4 operations cannot be performed when set to "Rec
Select" .
A4 Remote ID
Set remote control ID.
Match the ID setting of the remote control unit and the receiver.
[Selectable items]
• When changing the remote ID, also change the AMP , iPod and
NET/DTU modes of the main remote control unit at the same time
(vpage 69).
• When changing the remote ID, also change the sub remote control
unit at the same time (vpage 74).
A5 2Way Remote
Set when using the 2-way remote control unit.
[Selectable items] Used
When using a 2-way remote control unit (RC-7000CI and RC-7001RCI,
sold separately), set this to "Used" .
NOTE
• When using the 2-way remote control unit, connect to the Port 1 RS-
232C connector.
• If GUI menu "Manual Setup" – "Option Setup" – "2Way Remote"is
110Hz 120Hz
set to "Used" , you cannot use port 1 of the RS-232C terminal for the
external controller.
1 2 3 4
Not Used