Setting The Crossover Frequency - Denon AVC-A11XV Operating Instructions Manual

ENGLISH
Advanced Setup – Part 2
3 CURSOR D D H H
Press the or
select the "Surr. Sp.", then press the
CURSOR F F G G
or button to select the
surround speaker(s) from which you
want to produce the test tone (A, B or
A+B).
Surr. Sp. : A
Adjusts the balance of the playback level between
the channels when using surround speaker A.
Surr. Sp. : B
Adjusts the balance of the playback level between
the channels when using surround speaker B.
Surr. Sp. : A + B
Adjusts the balance of the playback level between
the channels when using surround speakers A and
B at the same time.
The "Surr. Sp." can only be selected when both
surround speakers A and B have been selected
at the System Setup Menu (when both A and B
have been set to "Large" or "Small").
4
CURSOR D D H H
Press the or
select the "Test Tone Start", then press
CURSOR F F
the button to select the
"Yes".
5
The "Auto" mode is selected:
CURSOR F F G G
Press the or
adjust all the speakers to the same
-1
volume.
• The test tones are emitted from each
speaker in the following order, at 4-second
intervals the first time and second time
around, 2-second intervals the third time
around and on:
FL C FR SR
2spkrs
SW SL SBL SBR
SB
1spkr
When the surround back speaker setting is set to
"1spkr" for "Speaker Configuration", this is set
to "SB".
Example:
button to
When the volume is set to –11.5 dB while
the test tone is being produced from the
Front Lch speaker.
The volume can be adjusted between –12 dB and
+12 dB in units of 0.5 dB.
5 The "Manual" mode is selected:
CURSOR D D
Press the
select the speaker, then press the
-2
CURSOR F F G G
or button to adjust all the
speakers to the same volume.
Example: "Manual" mode is selected.
button to
6
ENTER
Press the button to enter the
setting.
• The "Channel Level" screen reappears.
button to
• To cancel the settings, press the CURSOR H H button to
select the "Level Clear" and "Yes" on the "Channel
Level" screen, then make the settings again.
• When adjusting the level of an active subwoofer
system, you may also need to adjust the
subwoofer's own volume control.
• When you adjust the channel levels while in the
H H
or button to
SYSTEM SETUP CHANNEL LEVEL mode, the
channel level adjustments made will affect all
surround modes. Consider this mode a Master
Channel Level adjustment mode.
• After you have completed the SYSTEM SETUP
CHANNEL LEVEL adjustments, you can then
activate the individual surround modes and adjust
channel levels that will be remembered for each of
those modes. Then, whenever you activate a
particular surround sound mode, your preferred
channel level adjustments for just that mode will be
recalled. Check the instructions for adjusting channel
levels within each surround mode (
32).
• You can adjust the channel levels for each of the
following surround modes: PURE DIRECT/DIRECT,
STEREO, DOLBY/DTS SURROUND, HOME THX
CINEMA, 7CH STEREO, WIDE SCREEN, SUPER
STADIUM, ROCK ARENA, JAZZ CLUB, CLASSIC
CONCERT, MONO MOVIE, VIDEO GAME and
MATRIX.
• When using either surround speakers A or B, or
when using surround speakers A and B at the same
time, be sure to adjust the balance of playback levels
between each channel for the various selections of
"A", "B" and "A+B".
2 Adjusting the test tone using the
remote control unit
• As described below, this adjustment can be
accomplished via the with remote control unit.
• Adjusting with the remote control unit using the test
tones is only possible in the "Auto" mode and only
effective in the
SURROUND) and HOME THX CINEMA modes. The
adjusted levels for the different modes are
automatically stored in the memory.
55
ENGLISH
1
Press the
• Test tones are output from the different
speakers.
2
Press the
adjust the channel level so that the
volume of the test tones is the same for
all the speakers.
3
After completing the adjustment, press
TEST TONE
the

Setting the Crossover Frequency

• Set the crossover frequency according to the low
frequency response characteristics of the various
(front, center, surround and surround back) speaker
systems.
• If a connected main or surround loudspeaker has a
specified –3 dB low frequency response rolloff,
adjust the crossover frequency for that speaker to
match the specified low frequency response limit –
e.g. 80 Hz.
page 31, • When a speaker is set to SMALL, low frequencies in
that channel that are below the crossover frequency
are directed to the system's subwoofer(s), or to
speakers that are set to LARGE, for systems with no
connected subwoofer(s).
1
Press the
select the "Crossover Frequency" at the
"Speaker Setup" menu, then press the
ENTER
• Display the "Crossover Frequency" screen.
STANDARD (DOLBY/DTS
Advanced Setup – Part 2
TEST TONE
button.
CURSOR F F G G
or button to
button again.
CURSOR D D H H
or button to
button.