Multi-Source Recording / Playback; Playing One Source While Recording Another (Rec Out Mode); Recording Dolby Digital And Dts Multi Channel Sources; Dolby Headphone Recording - Denon AVC-A11XV Operating Instructions Manual

Advanced Operation
ZONE3/REC SELECT
FUNCTION DIRECT/STEREO
POWER PHONES INPUT MODE
PURE DIRECT

Multi-source recording / playback

2 Playing one source while recording
another (REC OUT mode)
1
ZONE3/REC SELECT
Press the button
until "RECOUT SOURCE" appears on
the display.
• The "REC" indicator lights.
D V D
R E C O U T S O U R C E
2
FUNCTION
Turn the knob to select the
source you wish to record.
3
Set the recording mode.
For operating instructions, refer to the manual of
the component on which you want to record.
• To cancel, turn the FUNCTION knob and select
"SOURCE".
• Recording sources other than digital inputs selected
in the REC OUT mode are also output to the ZONE3
audio/video output terminals.
• When the REC OUT mode is selected, the ZONE3
button on the remote control unit cannot be
operated.
• When "ZONE2 SELECT" is selected at "Digital Out
Assign", the source switches in association with the
"ZONE2 SELECT" mode for the OPTICAL2 OUT
connector ( page 52).
SOURCE
FUNCTION
INPUT MODE
2 Recording Dolby Digital and DTS
multi channel sources
• With this set it is possible to record Dolby Digital and
DTS multichannel signals converted into 2-channel
analog signals.
• The recording signals are output to the TAPE and
VCR output terminals.
• Down-mixed analog signals converted into digital
signals are output from the OPTICAL 2, 3 and 4
digital output terminals at this time.
1
ZONE3/REC SELECT
Press the
until "RECOUT SOURCE" appears on
the display.
2
INPUT MODE
Press the button to set
the input mode according to the source
to be played.
3
DIRECT/STEREO
Press the button to set
the surround mode.
• The multichannel digital signals are down-
mixed and output to the TAPE and VCR
output terminals.
4
Set the recording mode.

2 Dolby Headphone recording

When REC OUT mode is set to "SOURCE", with the
AVC-A11XV it is possible to output signals encoded in
the Dolby Headphone mode from the recording output
terminal and record them on a separate recorder.
1
The Dolby Headphone play mode is set
SURROUND
when headphones are connected to the
PHONES
jack during playback in the
STEREO
DOLBY/DTS surround mode.
DIRECT
• When this is done, signals encoded in the
Dolby Headphone mode are automatically
output from the recording output terminals
(analog and digital) and can be recorded.
2
Select the parameters and set the
desired mode.
• Start recording.
Refer to the "The Dolby Headphone" (
28).
NOTE:
• Do not disconnect the headphones during
recording.

Last function memory

button • This unit is equipped with a last function memory
which stores the input and output setting conditions
as they were immediately before the power is
switched off.
This function eliminates the need to perform
complicated resetting when the power is switched
on.
• The unit is also equipped with a back-up memory.
This function provides approximately one week of
memory storage from when the main unit's power
switch is off and with the power supply cord
disconnected.
40
ENGLISH
Advanced Operation

Initialization of the microprocessor

In very rare instances, the AVC-A11XV internal
microprocessor might lock up, or otherwise cause
mis-operation. This might be caused due to an AC line
surge or line spike noise, or by static electric discharge
on or nearby the unit, or to connected components. If
the condition cannot be corrected by powering off the
unit, including disconnection of the Power supply cord
for a period of ten minutes and subsequent re-
connection, then the unit may have to be re-initialized.
Doing so will restore the microprocessor to its original
out-of-the-box state, with all custom memories and
settings erased, and the original factory default
settings restored. Only use this procedure if you are
sure that the microprocessor requires re-initialization.
1
Switch off the unit using the main unit's
POWER
switch.
page
2
PURE DIRECT
Hold the following
DIRECT/STEREO
button and
POWER
and turn the main unit's
on.
3
Check that the entire display is flashing
with an interval of about 1 second, and
release your fingers from the 2 buttons.
• The microprocessor will be initialized.
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the settings
are reset to the default values (the values set upon
shipment from the factory).
ENGLISH
button,
switch