Turning On The Power; Starting Auto Setup; Extra Setup; Preliminary Measurements - Denon AVC-A11XV Operating Instructions Manual

ENGLISH
Easy Setup and Operation

Turning on the power

1
Turn on your subwoofer.
Set the volume to halfway and set the crossover
frequency to the maximum or Low pass filter off
if your subwoofer can adjust the output volume
and the crossover frequency.
Some subwoofers have a standby mode. Be sure
to turn this function off before performing the
Auto Setup procedure.
2
Turn on your monitor (TV).
3
POWER
Press the switch.
ON:
¢
The power turns on and the power indicator lights.
Set the POWER switch to this position to turn the
power on and off from the included remote control
unit.
£ OFF:
The power turns off and indicator is off.
In this position, the power cannot be turned on and
off from the remote control unit.
4
ON/STANDBY
Press the switch on the
ON
main unit or button on the remote
control unit.
• When pressed, the power turns on and the
display lights.
• When pressed again, the power turns off,
the standby mode is set and the display
turns off.
The sound is muted for several seconds, after
which the unit operates normally.
Whenever the ON/STANDBY button is in the
standby state, the apparatus is still connected to
the AC line voltage. Please be sure to turn off the
POWER switch or unplug the cord when you
leave home for, say, a vacation.
5
AMP
Press the button to select the
"AMP" (only when operating with the
remote control unit).

Starting Auto Setup

1
SETUP
Press the button.
• Display the "System Setup Menu".
2 D D H H
CURSOR
Press the or button to
select the "Auto Setup / Room EQ",
ENTER
then press the button.
• Display the "Auto Setup / Room EQ" menu
screen.
3
CURSOR D D H H
Press the or button to
select the "Auto Setup", then press the
ENTER
button.
• Display the "Auto Setup" screen.
The message "Connect Microphone"
displayed if no microphone is connected. If so,
connect the auto setup microphone.

Extra Setup

The AVC-A11XV has seven available amplifier
channels, some of which can be assigned for
powering speakers in ZONE2 and ZONE3, depending
on the speaker system complement in the main room.
If this functionality is not needed, skip this "Extra
Setup" procedure and proceed to "Preliminary
Measurements" ( page 9, 10).
1 CURSOR D D H H
Press the or
select the "Extra Setup", then press the
CURSOR F F
button.
• Switch to the "Extra Setup" screen.
2 CURSOR D D H H
Press the or
choose the setting you want to change,
ENTER
then press the button.
• Switch to the setting screen.
For instructions on making the "Channel Setup"
settings ( page 49).
For instructions on making the "Setting the
Power Amplifier Assignment" settings (
page 49, 50).
The speakers measured with this Auto Setup
procedure are based on the setting of these
"Channel Setup" and "Power Amp Assign"
functions.
3
Once the settings are completed, press
is
ENTER
the button at the each setting
screen.
• The "Extra Setup" menu reappears.
4
CURSOR
D D or H H button to
Press the
select the "Exit", then press the
button.
• Return to the "Auto Setup" screen.
9
ENGLISH
Easy Setup and Operation

Preliminary Measurements

• This procedure is used to automatically determine
the background noise, whether or not speakers are
connected, and the polarities of the connected
speakers.
• To avoid affecting the measurements, turn off the
air-conditioner or any other device that makes noise
and take the measurements with the room as quiet
as possible.
button to
1
CURSOR D D
Press the
select the "Start", then press the
CURSOR
F F button.
• Start the preliminary measurements.
button to
The screen shown at the below appears once the
preliminary measurements are completed.
2
ENTER
Press the button.
• Switch to the "Speaker Detect Check"
screen.
[ First screen ]
ENTER
H H
or button to