Setting The Component In Assign; Setting The Video Convert Mode - Denon AVC-A11XV Operating Instructions Manual

ENGLISH
Advanced Setup – Part 1
• If a monitor is connected with an HDMI cable but the
monitor is not compatible with HDMI audio signal
playback, only the video signals are output to the
monitor from the AVC-A11XV (DVI mode).
Press the STATUS button to check which mode is set
for outputting HDMI signals from the AVC-A11XV
(HDMI and DVI modes).
• Input signals input from the analog and digital
terminals are not output to the TV.
• With HDMI, the video and audio signals are
transferred simultaneously. When HDMI is assigned
to an input source, the digital audio input assignment
switches to HDMI along with the video input.
When this setting is made for input sources to which
a digital audio input (DENON LINK, IEEE1394 etc.) is
previously assigned, the digital audio assignment is
set to HDMI.
In this case, reassign the digital input using the
procedure described at "Digital In Assign" (
page 42) and "IEEE1394 Assign" (

Setting the Component In Assign

This setting assigns the component video input
terminal of the AVC-A11XV for the different input
sources.
1
CURSOR D D H H
Press the or
select the "Component In Assign" at the
"Video Setup" menu, then press the
ENTER
button.
• Display the "Component In Assign" screen.
2 CURSOR D D
Press the
select the input source, then press the
CURSOR F F G G
or button to select the
component video input terminal.
Select from among 1-RCA to 3-RCA.
If the same component video input terminal is
selected, the setting for the input source that
was previously assigned switches to "NONE".
If "Yes" is selected for "Default", the settings
are reset to the default values.
3 ENTER
Press the button to enter the
setting.
• The "Video Setup" menu reappears.

Setting the Video Convert Mode

page 43, 44).
Select the input signal to be output to the composite
S-Video and component monitor output terminals
using the video conversion function.
1
CURSOR D D
Press the
select the "Video Convert Mode" at the
"Video Setup" menu, then press the
ENTER
button.
button to
• Display the "Video Convert Mode" screen.
H H 2 CURSOR D D
or button to Press the
select the input source, then press the
CURSOR F F
or
mode as below.
AUTO Component
The details in each mode are as follows.
AUTO:
When there are multiple input signals, the input
signals are detected and the input signal to be
output from the video monitor output terminal is
selected automatically in the following order:
component video, S-Video, composite video.
Component:
The signal connected to the component video
terminal is always played.
The component input signal is down–converted
and output from the composite and S-Video
monitor output terminal.
No image is output from the monitor output
terminal when there is no input signal to the
component input terminal.
S-Video:
H H
The signal connected to the S-Video terminal is
or button to
always played.
The S-Video input signal is converted and output
from the composite and component monitor
output terminal.
Video:
The signal connected to the composite video
terminal is always played.
The composite video input signal is up-converted
and output from the S-Video and component
monitor output terminals.
OFF:
The convert function does not operate.
The video signal input from the video input
terminal is only output to the video monitor out
terminal.
The S-Video signal input from the S-Video input
terminal is only output to the S-Video monitor out
terminal.
The component input signal input from the
component input terminals is only output to the
component monitor output terminals.
45
ENGLISH
H H 3
Press the
or button to
setting.
G G
• The "Video Setup" menu reappears.
button to select the
S-video Video OFF
• Down-converting from the component video signal
to the S-Video and composite video signal is possible
only when the resolution of a component video
signal is 480i / 576i.
• For optimum video performance, THX recommends
that video pass through (bypass) is used.
• When a non-standard video signal from a game
machine or some other source is input, the video
conversion function might not operate. If this
happens, please set the conversion mode to OFF.
• When the video conversion function has been used,
information such as that of text broadcasts which
has been added to the video signal might not be
output. If this happens, please set the conversion
mode to OFF.
Advanced Setup – Part 1
ENTER
button to enter the