Agilent Technologies InfiniiVision 3000 X-Series Programmer's Manual page 1272

Index
hostname, 52
I
I1080L50HZ, 944, 948
I1080L60HZ, 944, 948
I2C demo signal, 283
I2S alignment, 690
I2S audio channel, 699
I2S clock slope, 692
I2S CLOCk source, 694
I2S DATA source, 695
I2S demo signal, 284
I2S pattern data, 700
I2S pattern format, 702
I2S range, 703
I2S receiver width, 693
I2S SEARch commands, 820
I2S serial bus commands, 688
I2S serial decode base, 691
I2S serial search, audio channel,
I2S serial search, data, 823
I2S serial search, format, 824
I2S serial search, mode, 822
I2S serial search, range, 825
I2S transmit word size, 705
I2S trigger operator, 697
I2S triggering, 629
I2S word select (WS) low, 706
I2S word select (WS) source, 696
id mode, 668
ID pattern, CAN trigger, 667
identification number, 170
identification of options, 173
identifier, LIN, 726
idle, 898
idle until operation complete, 172
IDN (Identification Number), 170
IEC 61000-3-2 standard for current harmonics
analysis, 544
IEEE 488.2 standard, 163
IIC address, 711
IIC clock, 709
IIC data, 710, 712
IIC data 2, 713
IIC SEARch commands, 826
IIC serial decode address field size,
IIC serial search, address, 829
IIC serial search, data, 830
IIC serial search, data2, 831
IIC serial search, mode, 827
IIC serial search, qualifier, 832
IIC trigger commands, 707
IIC trigger qualifier, 714
IIC trigger type, 715
IIC triggering, 630
image format, 612
image invert graticule colors, 613
image memory, 222
image palette, 614
image, save, 610
image, save with inksaver, 613
1272
impedance, 267
infinity representation,
initial load current, transient response
analysis,
initialization, 60,
initialize, 176,
initialize label list,
initiate acquisition,
inksaver, save image with,
input coupling for channels,
input for integrate, DC offset correction,
input impedance for channels, 267,
input inversion for specified channel,
input power, 479
inrush current,
inrush current analysis, 547, 548,
inrush current expected,
insert label, 269
installed options identified,
instruction header,
instrument number,
821
instrument options identified,
instrument requests service,
instrument serial number,
instrument settings,
instrument status,
instrument type,
integrate DC offset correction,
integrate math function, 326, 347,
INTegrate source for function,
internal low-pass filter, 264,
introduction to :ACQuire commands,
introduction to :BUS<n> commands,
introduction to :CALibrate commands,
introduction to :CHANnel<n> commands,
introduction to :DEMO commands,
introduction to :DIGital<d> commands,
introduction to :DISPlay commands,
introduction to :EXTernal commands,
introduction to :FUNCtion commands,
introduction to :HARDcopy commands,
introduction to :LISTer commands,
introduction to :MARKer commands,
introduction to :MEASure commands,
introduction to :POD<n> commands,
introduction to :RECall commands,
introduction to :SAVE commands,
708
introduction to :SBUS commands,
introduction to :SYSTem commands,
introduction to :TIMebase commands,
introduction to :TRIGger commands,
introduction to :WAVeform commands,
introduction to :WGEN commands,
introduction to :WMEMory<r>
commands,
introduction to common (*) commands,
introduction to root (:) commands,
invert graticule colors for hardcopy, 363,
invert graticule colors for image,
inverted masks, bind levels,
inverting input for channels,
IO library, referencing,
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
1145
593
63
858
306
199
613
265
343
1053
268
483
549
573
173
1139
170
173
183
220
358
70
170
343
981
1059
318
227
242
251
263
281
290
298
317
326
358
375
380
406
523
598
607
629
852
866
877
961
998
1033
163
190
1064
613
516
268
62
IP address, 52
IronPython, SCPI.NET example, 1260
K
key disable, 856
key press detected in Standard Event Status
Register, 168
knob disable, 856
known state, 176, 858
L
label, 1050
label command, bus, 248
label list, 269, 306
label reference waveforms, 1037
label, ARINC 429 trigger, 645, 649,
label, digital channel, 292
labels, 269, 305, 306
labels to store calibration information,
labels, specifying, 298
LAN interface, 51, 54
LAN Settings softkey, 52
landscape layout for hardcopy, 364
language for program examples,
layout for hardcopy, 364
leakage into peak spectrum, 337
learn string, 171, 862
least significant byte first, 967
left reference, 870
legal values for channel offset, 270
legal values for frequency span,
legal values for offset, 346, 350
length for waveform data, 623
less than qualifier, 913
less than time, 910, 914, 923, 926
less than value for glitch search,
level for trigger voltage, 903, 911
LF coupling, 902
license information, 173
limits for line number, 944
LIN acknowledge, 720
LIN baud rate, 721
LIN demo signal, 283
LIN identifier, 726
LIN pattern data, 727
LIN pattern format, 730
LIN SEARch commands, 833
LIN serial decode bus parity bits,
LIN serial search, data, 836
LIN serial search, data format, 838
LIN serial search, data length, 837
LIN serial search, frame ID, 834
LIN serial search, mode, 835
LIN source, 722
LIN standard, 723
LIN sync break, 724
LIN trigger, 725, 729
LIN trigger commands, 717
LIN trigger definition, 1091
803
254
59
335
787
719