Agilent Technologies InfiniiVision 3000 X-Series Programmer's Manual page 1278

Index
start cursor, 1072
start measurement, 406
start print job, 373
start time, 914, 1072
start time marker, 1069
state memory, 179
state of instrument, 171, 862
statistics increment, 448
statistics reset, 450
statistics results, 438
statistics, max count, 449
statistics, relative standard deviation,
statistics, type of, 446
status, 182, 222, 224
Status Byte Register (STB), 180, 182, 183,
1109
status data structure clear, 165
status registers, 70
status reporting, 1105
STB (Status Byte Register), 180, 182, 183,
1109
steady state output voltage expected, 578,
579, 580
step size for frequency span, 335
stop, 199, 223
stop acquisition, 223
stop cursor, 1073
stop displaying channel, 198
stop displaying math function, 198
stop displaying pod, 198
stop on mask test failure, 512
stop time, 914, 1073
storage, 179
store instrument setup, 171, 179
store setup, 179
storing calibration information, 254
string variables, 68
string variables, reading multiple query results
into, 69
string variables, reading query results into
multiple, 69
string, quoted ASCII, 158
subnet mask, 52
subsource, waveform source, 985
subsystem commands, 3, 1143
subtract math function, 326, 347,
subtract math function as g(t) source,
sweep mode, trigger, 877, 888
sweep speed set to fast to measure fall
time, 425
sweep speed set to fast to measure rise
time, 441
switch disable, 856
switching level, current, 587
switching level, voltage, 590
switching loss per cycle, 474
switching loss power analysis, 585
sync break, LIN, 724
sync frame count (FlexRay), 676
syntax elements, 157
syntax rules, program data, 1142
syntax, optional terms, 157
1278
syntax, program message,
SYSTem commands,
system commands, 853, 854, 855, 856, 862,
864
system commands introduction,
T
table of current harmonics results,
tdelta, 1068
tedge, 452
451
telnet ports 5024 and 5025,
Telnet sockets,
temporary message,
TER (Trigger Event Register), 224,
termination conditions, mask test,
test sigma, mask test run,
test, self, 185
text, writing to display,
THD (total harmonics distortion),
threshold, 295, 527, 1051,
threshold voltage (lower) for
measurement,
threshold voltage (upper) for
measurement,
thresholds, 414,
thresholds used to measure period,
thresholds, how autoscale affects,
time base, 867, 868, 869, 870, 871,
time base commands introduction,
time base reset conditions, 177,
time base window, 873, 874,
time between points,
time buckets, 229,
time delay, 1093
time delay, Edge Then Edge trigger,
time delta, 1068
time difference between data points,
time duration, 914, 922, 923,
time holdoff for trigger,
time interval, 452, 454,
time interval between trigger and
occurrence,
time marker sets start time,
time measurements with X cursors,
981
time per division,
340
time record, 337
time reference, lister,
time specified,
time, calibration,
time, mask test run,
time, runt pulse search,
time, runt trigger,
time, start marker,
time, stop marker,
time, system, 864
time, transition search,
time, transition trigger,
time/div, how autoscale affects,
time-at-max measurement,
time-at-min measurement,
TIMebase commands,
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
1139
851
852
539
969
71
854
1112
508
513
854
546
1094
1066
1076
1069
433
193
1093
866
859
875
1068
230
892
989
926
882
1068
1074
1069
387
869
378
464
260
514
796
931
1072
1073
801
942
193
1070
1071
865
timebase vernier, 872
TIMebase:MODE, 66
time-ordered label list, 306
timeout, SPI clock, 742
timing measurement, 406
title channels, 269
title, mask test, 522
tolerance, automask, 498, 499
top of waveform value measured,
total frame count (CAN), 657
total frame count (FlexRay), 677
total harmonics distortion (THD),
total waveforms in mask test, 503
trace memory, 222
track measurements, 443
trademarks, 2
transfer instrument state, 171, 862
transforms, math, 326
transient response, 488
transient response analysis, 591, 592,
TRANsition SEARch commands,
transition search qualifier, 798
transition search slope, 799
transition search time, 801
transition trigger qualifier, 939
transition trigger slope, 940
transition trigger source, 800, 941
transition trigger time, 942
transmit word size, I2S, 705
tree traversal rules, 1143
trend measurement, 355
TRG (Trigger), 181, 183, 184
TRIG OUT BNC, 255
trigger armed event register, 207,
trigger burst, UART, 770
trigger channel source, 915, 947
TRIGger commands, 877
TRIGger commands, general, 879
trigger data, UART, 771
TRIGger DELay commands, 889
trigger duration, 922, 923
TRIGger EBURst commands, 896
TRIGger EDGE commands, 901
trigger edge coupling, 902
trigger edge slope, 905
trigger edge slope, Edge Then Edge
trigger, 894
trigger edge source, Edge Then Edge
trigger, 895
trigger event bit, 224
Trigger Event Register (TER), 1112
TRIGger FLEXray commands, 669
TRIGger GLITch commands, 907
trigger holdoff, 882
trigger idle, UART, 772
TRIGger IIC commands, 707
trigger level auto set up, 883
trigger level constants, 271
trigger level voltage, 903
trigger level, high, 884
trigger level, low, 885
TRIGger LIN commands, 717
465
546
595
797
209