Denon AVR-4520CI Owner's Manual page 146

Setting items
Distances Unit : Set the unit of distance.
Set distance from listening • Feet / Meters
position to speakers.
Step : Set the minimum variable width of the distance.
Measure beforehand the
• 1ft / 0.1ft
distance from the listening
• 0.1m / 0.01m
position to each speaker.
Set Defaults : The "Distances" settings are returned to the default
settings.
• Reset : Reset to the defaults.
• Cancel : Do not reset to the defaults.
When you select "Set Defaults" and press
ENTER
, the "Resets all of the distance
settings to the factory defaults?" prompt is
displayed. Select either "Reset" or "Cancel",
and press
Front L / Front R / F. Height L / F. Height R / F. Wide L / F. Wide R /
Center / Subwoofer 1
z2
Surr. Back L
z1 When the "Speaker Config." – "Subwoofer" setting (vpage 142)
is set to "1spkr", "Subwoofer" is displayed.
z2 When the "Speaker Config." – "Surr. Back" setting
is set to "1spkr", "Surr. Back" is displayed.
• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 141) and "Speaker Config." (vpage 142) settings.
• Default settings :
Front L / Front R / F. Height L / F. Height R / Front Wide L / Front Wide R /
Center / Subwoofer 1 / Subwoofer 2 : 12.0 ft (3.60 m)
Surround L / Surround R / Surr. Back L / Surr. Back R : 10.0 ft (3.00 m)
• Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
NOTE
Speakers set to "None" in "Speaker Config."
displayed.
DVD
Setting details
ENTER
.
z1 z1
/ Subwoofer 2 / Surround L / Surround R /
z2
/ Surr. Back R : Select speaker for distance setting.
(vpage
(vpage
Setting items
Levels
Set the volume of the test
tone to be the same when it
is output from each speaker.
142)
142) are not
143
Setting details
Test Tone Start : Output test tone.
• Front L / F. Height L / Center / F. Height R / Front R / F. Wide R /
z1
Surround R / Surr. Back R / Surr. Back L
z2
F. Wide L / Subwoofer 1 / Subwoofer 2
A test tone is output from the selected speaker. While listening to the
test tone, adjust the volume output from the selected speaker.
z1 When the "Speaker Config." – "Surr. Back" setting
is set to "1spkr", "Surr. Back" is displayed.
z2 When the "Speaker Config." – "Subwoofer" setting (vpage 142)
is set to "1spkr", "Subwoofer" is displayed.
z3 When "Subwoofer 1+2" is selected, you can adjust the volume of
Subwoofer 1 and Subwoofer 2 at the same time.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
When "Levels" is adjusted, the adjusted values are set for all the
sound modes.
NOTE
• Speakers set to "None" in the "Speaker Config."
settings are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Levels" is not displayed.
Set Defaults : The "Levels" settings are returned to the default settings.
• Reset : Reset to the defaults.
• Cancel : Do not reset to the defaults.
When you select "Set Defaults" and press
ENTER
, the "Reset all of the channel level
settings to the factory defaults?" prompt is
displayed. Select either "Reset" or "Cancel",
ENTER
and press .
Speakers
z1
/ Surround L /
z2 z3
/ Subwoofer 1+2 :
(vpage 142)
(vpage 142)
v See overleaf