Denon AVR-4520CI Owner's Manual page 128

Audyssey
Set Audyssey MultEQ ® XT 32, Audyssey Dynamic EQ ® , Audyssey Dynamic Volume ® , Audyssey LFC™
and Audyssey DSX ® . These can be selected after Audyssey ® Setup has been performed. For additional
information on Audyssey technology, please see page 193.
NOTE
• If you have not performed Audyssey ® Setup, or if you change the speaker settings after performing
Audyssey ® Setup, you may not be able to select Dynamic EQ/Dynamic Volume.
In this case, either perform Audyssey ® Setup over again or perform "Restore..."
return to the settings after Audyssey ® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the "Audyssey"
cannot be set.
Setting items
MultEQ ® XT 32
Audyssey : Optimize the frequency response of all speakers.
MultEQ ® XT 32
Audyssey Byp. L/R : Optimize frequency response of speakers except
compensates for both front L and R speakers.
time and frequency Audyssey Flat : Optimize frequency response of all speakers to flat
characteristics of the response.
listening area based Graphic EQ : Apply frequency response set with "Graphic EQ"
on Audyssey ® Setup
(vpage 127).
Off : Turn "MultEQ ® XT 32" equalizer off.
measurement results.
Selection is done from three
types of compensation
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
curves. We recommend the
selected after Audyssey ® Setup has been performed. "Audyssey"
"Audyssey" setting.
is automatically selected after performing Audyssey ® Setup. When
MultEQ ® XT 32 is the
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
prerequisite function for
illuminates.
Dynamic EQ, Dynamic
• After running Audyssey ® Setup, if the Speaker Configuration, Distance,
Volume and Audyssey
Channel Level, and Crossover Frequency have changed without
LFC™.
increasing the number of speakers measured, only
NOTE
When using headphones, "MultEQ ® XT 32" is automatically set to "Off".
"MultEQ ® XT 32", "Dynamic EQ" and "Dynamic Volume" settings are stored for each input source.
DVD
Default settings are underlined.
(vpage 40) to
Setting details
illuminates.
125
Setting items
Dynamic EQ On : Use Dynamic EQ.
Solve the problem of Off : Do not use Dynamic EQ.
deteriorating sound quality
is displayed when set to "On".
as volume is decreased
by taking into account
NOTE
human perception and
When the menu "Dynamic EQ" setting is "On", it is not possible to do
room acoustics. Works with
"Tone Control" (vpage 123) adjustment.
MultEQ ® XT 32.
Reference Level Offset 0dB (Film Ref) : This is the default setting and should be used when
Audyssey Dynamic EQ ® is
listening to movies.
referenced to the standard 5dB : Select this setting for content that has a very wide dynamic range,
film mix level. It makes such as classical music.
adjustments to maintain 10dB : Select this setting for jazz or other music that has a wider dynamic
the reference response range. This setting should also be selected for TV content as that is usually
and surround envelopment mixed at 10 dB below film reference.
when the volume is turned 15dB : Select this setting for pop/rock music or other program material
down from 0 dB. However, that is mixed at very high listening levels and has a compressed dynamic
film reference level is not range.
always used in music or
Setting is enabled when "Dynamic EQ" is "On" (vpage 125).
other non-film content.
Dynamic EQ Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard. Recommended
setting levels are shown at
right.
Audio
Setting details
v See overleaf