Page 1
MODIFICATION NOTICE. SERVICE MANUAL MODEL E1C E1K E1C AVR-4520CI AVR-4520 INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
CONTENTS ABOUT THIS MANUAL .............3 AUDIO/VIDEO (COMPONENT SIDE)........140 FRONT (COMPONENT SIDE) ..........140 What you can do with this manual ..........3 Using Adobe Reader (Windows version) ........4 CONNECT1 (COMPONENT SIDE) ........140 CONNECT2 (COMPONENT SIDE) ........140 SAFETY PRECAUTIONS ............6 APOWER (COMPONENT SIDE) ..........142 NOTE FOR SCHEMATIC DIAGRAM .........7 BRIDGE (COMPONENT SIDE) ..........142 NOTE FOR PARTS LIST ............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram (Ctrl+Shift+F) connector You can use the search function in Acrobat Reader to Click the Ref.
Using Adobe Reader (Windows version) Add notes to this data (Sign) Magnify schematic / printed wiring board The Sign function lets you add notes to the data in this diagrams - 1 manual. (Ctrl+Space, mouse operation) Save the file once you have finished adding notes. Press Ctrl+Space on the keyboard and drag the mouse to select the area you want to view.
Page 5
Magnify schematic / printed wiring board Magnify schematic / printed wiring board diagrams - 2 diagrams - 3 (Pan & Zoom function) (Loupe Tool function) The Loupe Tool function lets you magnify a specific The Pan & Zoom function lets you see which part of a magnified diagram is being shown in a separate window.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
TECHNICAL SPECIFICATIONS n Audio Section n Tuner section (E3 model) • Power amplifier (ANTENNA input – MEDIA PLAYER OUT) Rated output : [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 –15 Front : Receiving Range : 150 W + 150 W (8 Ω, 20 Hz – 20 kHz with 0.05 % T.H.D.) [FM] 87.5 MHz –...
Cursor d Cursor f Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Denon Official Service Distributor in your region if necessary. EXTENSION UNIT KIT 8U-110084S 2 Set...
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the reassembling, observe "Caution concerning disassembly and assembly!". •...
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
Page 12
(2) Remove the screws. Shooting direction: A (3) Cut the wire clamp band, then disconnect the FFC cables. FFC Cable Shooting direction: B Direction of photograph: C Direction of photograph: D...
Page 13
(4) Disconnect the connector wires. N1701 Shooting direction: B During removal, note the FRONT HDMI USB Board. Direction of photograph: D N603...
Page 14
(5) Cut the wire clamp band, then disconnect the connector wires. N803 N802 Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in FRONT PANEL SUB ASSY. NOTE DOOR is working ina fully open state.
2. RADIATOR(L) SUB ASSY RADIATOR(L) SUB ASSY Proceeding : TOP COVER → (1) Disconnect the connector wires, then remove the screws. Shooting direction: B...
Page 16
(2) Disconnect the connector wires. N9002 Shooting direction: B N9003 Shooting direction: A N502 N402 N302 N9004 N202 N102 Shooting direction: B Direction of photograph: D Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in RADIATOR(L) SUB ASSY.
3. RADIATOR(R) SUB ASSY Proceeding : TOP COVER RADIATOR(L) SUB ASSY RADIATOR(R) SUB ASSY → → (1) Disconnect the connector wires. N3901 N3902 Shooting direction: B Direction of photograph: C N9016 N9017 N9022 N902 N802 N702 N602 Direction of photograph: C Shooting direction: B Please refer to "EXPLODED VIEW"...
4. POWER TRANS RADIATOR(L) SUB ASSY RADIATOR(R) SUB ASSY Proceeding : TOP COVER → → POWER TRANS → (1) Cut wire clamp band, then disconnect the connector wires and remove the screws. N9010 N3701 N6012 Direction of photograph: D Shooting direction: B Shooting direction: D Shooting direction: B...
5. BACK PANEL SUB ASSY RADIATOR(L) SUB ASSY RADIATOR(R) SUB ASSY Proceeding : Proceeding : TOP COVER → → POWER TRANS BACK PANEL SUB ASSY → → (1) Remove the screws. Direction of photograph: B Direction of photograph: D Direction of photograph: C Direction of photograph: D...
Page 20
(2) Remove the screws, then disconnect the connector wires. N1808 Shooting direction: B N9009 N9010 Direction of photograph: D...
Page 21
(3) Remove the screws, then disconnect the connector wire and FFC cable. N1807 Shooting direction: A Direction of photograph: C Please refer to "EXPLODED VIEW" for the disassembly method of each PWB included in BACK PANEL SUB ASSY.
Service Related Selection mode STATUS SELECT mode”. (Refer to 31 page) When using multiple DENON AV receivers in the same room, make this Remote ID Setup mode DIMMER STATUS setting so that only the desired AV receiver operates. (Refer to 65...
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "Power operation ( X )" button to turn on the power while pressing the "SETUP" and "OPTION" buttons. Now, press the "OPTION"...
Page 26
i Ethernet(DM860A) 1st Boot Loader, Hardware ID : E t h e r n e t F B L Upper Lower * * * * * * - A A o Ethernet(DM860A) 2nd Boot Loader : E t h e r n e t S B L Upper Lower...
Page 27
1.3. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t , y , u , i , o . Condition Status FL Display Trouble shooting •...
Page 28
Condition Status FL Display Trouble shooting When DSP3 code boot is performed, the DSP FLAG0 port does not change to "H" D S P 3 E R R O R even if DSP reset is executed. Before DSP3 command is issued, the D S P 3 E R R O R DSP BUSY port does not change to "L".
Page 29
1.4. Version display on the Setup Menu Use the following procedure to display the firmware version. (1) Press the "SETUP" button on the remote control. (2) Select "General-Information-Firmware". A version with 12 digits is displayed as shown in the following image. AVR-4520 GUI Image 0215-7241-1281 0215-7241-1281...
2. PANEL/REMOTE LOCK Selection mode 2.1. Behavior specifications In this mode, you can switch between the PANEL LOCK MODE and the Mode for preventing remote control acceptance. 2.2. Starting up Press the "Power operation ( X )" button to turn on power while pressing the "STATUS" and "INFO" buttons. Press the "Cursor d / f "...
3. Service Related Selection mode 3.1. Behavior specifications In this mode, you can switch between the Diagnostic mode (SERVICE CHECK), the Displaying the protection mode (PROTECTION), the 232C clear mode (RS232C RESET) and the operation information (OP INFO). 3.2. Starting up Press the "Power operation ( X )"...
Page 33
PROTECTION DIAGRAM AVR4520 ASO/DC/THERMAL PROTECTION DIAGRAM 8U-110130-11 L AMP CONNECT UNIT 8U-110130-10 R AMP CONNECT UNIT 8U-110130 POWER L AMP UNIT 8U-110130 POWER AMP R UNIT N9032 8U-310116 DIGITAL UNIT N9006 N9021 23P-SOCKET(C125Z2) 23P-PLUG(C125Z1) 23P-PLUG(C125Z1) TR Thermal TR Thermal TR_THERMAL_B TR_THERMAL_A 109 PE0 ASODET...
Page 34
3.4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode 3.4.1. Specification This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 3.4.2. Starting diagnostic mode Press the "Power operation ( X )" button to turn on power while pressing the "ZONE/REC SELECT" and "STATUS" buttons. Select "1.
Page 35
Output sequence of remote control codes Confirmation item Contents of confirmation Setting and display Details of how to operate remote controller *a) Remarks ※ It is useful to form a macro program. *b) qKEY 5/JKL (Main Zone) ·Input : HDMI (Signal of PCM2ch, DolbyDigital or DTS) / Output : HDMI Audio (signal) Path Audio : AVR(When checking the audio output 1.Press [AVR]...
Page 36
Output sequence of remote control codes Confirmation item Contents of confirmation Setting and display Details of how to operate remote controller Remarks ※ It is useful to form a macro program. ·Input : Analog / Output : Speakers (Front wide L/R) Amp Assign (signal) Path Amp assign : 7.1ch+ZONE2/3-MONO 1.Press [AVR]...
Page 49
fig.10 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 50
ANALOG I2S_DAC PCM1795 SPDIF_COAX1 DA-SBR OUTPU SPDIF_COAX2 AUDIO SPDIF_OPT1 SPDIF_OPT2 PLLOUTCLK BLOCK DA-FHL OUTPUT MAIN DAC I2S_DAC PCM1795 DIAGRAM DENON LINK HD DA-FHR module OUTPUT PLLOUTCLK DA-FWL OUTPUT MAIN DAC I2S_DAC PCM1795 DA-FWR OUTPUT SPDIF_OPT1 OPTICAL1 SPDIF_OPT2 OPTICAL2 SPDIF_COAX1 COAXIAL1...
Page 51
fig.11b H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 52
fig.12a x8 32Mb x8 32Mb SDRAM SDRAM 42S83200D 42S83200D 860_MAINCPU_CONNECTION 860_MAINCPU_CONNECTION NAND FLASH I P O D HUB_MAINCPU_CONNECTION MAIN CPU HUB_MAINCPU_CONNECTION COPROCESSOR H27U1G8F2DTR 2.0B or 2.0C USB_SEL USB_SEL for MEMORY/IPOD USB1 FRONT I2S_860 INPUT SPDIF DIGITAL SPDIF_860 AUDIO for MEMORY/HDD DM860A USB2 REAR...
Page 53
MAIN DAC ANALOG I2S_DAC PCM1795 SPDIF_COAX1 DA-SBR OUTPU SPDIF_COAX2 AUDIO SPDIF_OPT1 PLLOUTCLK SPDIF_OPT2 BLOCK DA-FHL MAIN DAC OUTPUT DIAGRAM DENON LINK HD I2S_DAC PCM1795 DA-FHR module OUTPUT PLLOUTCLK DA-FWL OUTPUT MAIN DAC I2S_DAC PCM1795 DA-FWR OUTPUT SPDIF_OPT1 OPTICAL1 SPDIF_OPT2 OPTICAL2...
Page 54
fig.12c H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 56
ANALOG I2S_DAC PCM1795 SPDIF_COAX1 DA-SBR OUTPU SPDIF_COAX2 AUDIO SPDIF_OPT1 SPDIF_OPT2 PLLOUTCLK BLOCK DA-FHL OUTPUT MAIN DAC I2S_DAC PCM1795 DIAGRAM DENON LINK HD DA-FHR module OUTPUT PLLOUTCLK DA-FWL MAIN DAC OUTPUT I2S_DAC PCM1795 DA-FWR OUTPUT SPDIF_OPT1 OPTICAL1 SPDIF_OPT2 OPTICAL2 SPDIF_COAX1 COAXIAL1...
Page 57
fig.13c H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 58
fig.14a H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C EXT-SW VOLUME IC1 EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 59
ANALOG I2S_DAC PCM1795 SPDIF_COAX1 DA-SBR OUTPU SPDIF_COAX2 AUDIO SPDIF_OPT1 SPDIF_OPT2 PLLOUTCLK BLOCK DA-FHL OUTPUT MAIN DAC I2S_DAC PCM1795 DIAGRAM DENON LINK HD DA-FHR module OUTPUT PLLOUTCLK DA-FWL OUTPUT MAIN DAC I2S_DAC PCM1795 DA-FWR OUTPUT SPDIF_OPT1 OPTICAL1 SPDIF_OPT2 OPTICAL2 SPDIF_COAX1 COAXIAL1...
Page 60
fig.15 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 61
fig.16 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 62
fig.17 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 63
fig.18 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 64
fig.19 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 65
fig.20 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 66
fig.21 H/P OUT PREOUT HDAM Mz ONLY PRE_FL PRE_FR PRE_C PRE_SW1 PRE_SW2 PRE_SL PRE_SR PRE_SB L PRE_SBR PRE_FHL PRE_FHR 8ch EXT.IN PRE_FWL PRE_FWR EXT-FL EXT-FR EXT-C VOLUME IC1 EXT-SW EXT-FL (FLIN1) 9ch AMP SP OUT PRE_Z2L EXT-SL DA-FL (FLIN2) PREOUT R2A15220FP TONE PRE_Z2R...
Page 67
3.5. Errors checking mode (Displaying the protection history) 3.5.1. Specifications Error mode (Displaying the protection history): When the set is started up in this mode, the error information is displayed. 3.5.2. About the display on the FL display When the "STATUS" button is pressed after setting the error (protection history display) mode is set, a history like the one shown below is displayed, depending on the conditions.
Page 68
3.5.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the set in error (protection display) mode and display the error, then press and hold down the "ENTER" button for 3 seconds. P R O T E C T H I S T O R Y Upper...
Page 69
Operation Info mode 3.7. 3.7.1. Specifications This mode displays the accumulated operating time, power on count, counts for each protection on the set. 3.7.2. About the display on the FL display When the set has started in the Operation Info mode, press the "STATUS" button to display information in the following order.
4. Additional Source mode 4.1. Specifications • The Additional Source setting is added for the custom installer. When the setting is "ON", AUX3-7 is added as a Source. It is possible to add the number of Sources for use by assigning various input connectors in Input Assign Menu. •...
The same operation cannot be accepted for one minute after the last 860 Reboot. 7. Remote ID Setup mode 7.1. Specifications When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates. 7.2. Setting the AV receivers Starting up: Turn on the power, then press and hold down the "STATUS"...
7.3. Setting the Remote control unit (1) Press and hold RC SETUP for at least 3 seconds. indicator flashes twice on the remote control unit. “SETUP” and (2) Use ui to display “RC-ID” on the remote control unit and press ENTER. (3) Use ui to set the remote ID and press ENTER.
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to DENON Official Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 74
(2) When DSP STAY is removed, put some shock absorbing material there so that the DSP board (8U-310115) does not come in contact with the digital board (8U-310116). To verify the element under the DSP board through an oscilloscope, etc., remove the DSP board, pull out the lead, and reinstall the DSP board before verification.
(1) Personal Computer (Installed "DFW_0062_AVR4520_(Rev.x.x.x).exe". (2) RS-232C cable (9P (Male), Straight). NOTE : Refer to "The Operating Manual for updating of DENON AV receiver firmware". 1.2. Connection of AV receiver (1) Confirm the power on/off switch of the AV receiver is turning off.
Page 76
1.4. Run the DFW Run the "DFW_0062_AVR4520_(Rev.x.x.x).exe" on desktop of PC. 1.5. Communication check (1) Select the serial port number of RS-232C in PC. (2) Click the "Check Comm." button. (3) When connection is good, then you can see the "Communication check OK." message. (4) If connection is not good, then you can see the "Communication check NG"...
Page 77
1.6. Download the firmware (1) Click the "Load" button. (2) Download the firmware from the specified download source to PC. XXX-XXXX XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin...
Page 78
1.7. Complete the firmware updating (1) Click the "Update" button. XXXXXXXX XXXXXXX (2) When writing of the firmware is completed, the power of AV receiver turns on automatically and you can see the "Update completed" message. (3) If you can’t complete the firmware update, please retry the firmware update from "1.3. Turn on the AV receiver" (Forced Update Mode ).
2. How to update by DPMS You can update the firmware by downloading the latest version from the Internet. 2.1. Connecting to the Network (1) System requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Setting Internet Computer...
Page 80
2.3. About the error code See the table below for error codes, details of faults, and coping strategies when the firmware is updated through DPMS (Denon Product Management Server). Error Details of Error code Display Coping strategies Code Reset and update again.
Page 81
Error Details of Error code Display Coping strategies Code Main CPU failed to receive firmware M a i n * * * m i n Turn off and on the power. Updating for rewriting sent from DM860A starts automatically. U p d a t i n g f a i l (when an error occurred) There was invalid data in the...
Page 82
Error Details of Error code Display Coping strategies Code Check the network connection. M a i n * * * m i n Connection to DPMS timed out Carry out the update in an environment when Main CPU was rewritten. C o n n e c t i o n F a i l 3 9 that has little network load.
Page 83
Error Details of Error code Display Coping strategies Code NACK was received when "L" S u b * * * m i n Turn off and on the power. Updating command sent to Sub CPU, DSP, starts automatically. U p d a t i n g f a i l PLD etc.
Page 84
Error Details of Error code Display Coping strategies Code Acquisition of (Application Mode) Check the network connection. E t h e r I M G * * * m i n IP address failed before rewriting Carry out the update in an environment DM860A was rewritten (when timed C o n n e c t i o n F a i l A 1 that has little network load.
Device display during firmware update Target of device when firmware updated. Target of device Display Error cpde M a i n * * * m i n 10~15 Main 36~3F U p d a t i n g * * % 50~52 S u b * * * m i n 54~58 U p d a t i n g...
Page 86
3.2. Unzip Download File Pleases unzip the downloaded file on PC. AVR4520 E3 USB_AVR-4520E3_000100620100-0001.zip You can find "firmwares" folder after unzipped. Please copy that folder to USB flash drive. You have to put "firmwares" folder on root directly on USB flash drive(memory). copy to USB flash drive 3.3. Copy for USB flash drive 000100620100...
Page 87
USB location is below USB memory root Model Name Model Area Product ID North America (E3) 000100620100 AVR4520 Europe (E2) 000100620200 China (E1C) 000100620500 + firmwares + 000100620100 + APLD.bin + DSP1.bin + DSP2.bin + DSP3.bin + enc_update.xml + GUI.bin + IMG.bcd + MAIN.bin + SBL.bcd...
Page 88
3.5. Start update Turn on the power of this unit in the "STATUS" + "OPTION" button. 3.6. "USB Update Start" on FL Display After arround half minutes, FL display shows the following message. FL Display * F I R M W A R E U P D A T E Upper Lower...
Page 89
3.9. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error Details of Error code Display Coping strategies Code C o n n e c t i o n f a i l Disconnect and connect the USB Unable to detect USB.
Page 90
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. M a i n * * * m i n BlockWrite failed while rewriting Main. If the FL display stops at the Error U p d a t i n g f a i l display, press and hold the "Power...
Page 91
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. M a i n * * * m i n No FirmwareFile for If the FL display stops at the Error FirmwareDownload.
Page 92
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. Abnormal data in UpdatePacket S u b * * * m i n received from DM860A (DataLength/ If the FL display stops at the Error U p d a t i n g f a i l display, press and hold the "Power...
Page 93
Error Details of Error code Display Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. E t h e r I M G * * * m i n No FirmwareFile in USB. If the FL display stops at the Error F i l e s N o t F o u n d display, press and hold the "Power operation ( X )"...
Page 94
3.10. Device display during firmware update Display of target device during firmware update. Target of device Display Error cpde M a i n * * * m i n 10~15 Main 36~3B, 3F U p d a t i n g * * % 50~52 S u b * * * m i n 54~57...
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
2. Analog video Perform the operation below beforehand.- b Check it whether connection cable and Monitor are normal. b VIDEO Convert is set to ON. b COMPONENT signal is set to 480i. b ZONE2 is set to POWER ON. b Function is set to CBL/SAT. MONITOR OUT (CVBS or COMPONENT) output NG Input Input...
Page 105
Input CVBS,COMP Check power supply voltage. • Defective connection of N3701. 8U-210119-1 AUDIO/VIDEO UNIT. • Power supply IC (U3701 or U3702) flaw. V+3.3V : U3701 Out pin V-5V U3702 Out pin Check of the I C control signal of video selector IC(U3703).
Page 106
AUDIO/VIDEO UNIT flaw. Extend DIGITAL UNIT using a jig. Check power supply voltage and I2C control signal of video selector IC (U3703). Power supply IC (U3701 or U3702) flaw. V+3.3V : C3748 + Defective connection of N4004 or N4007. V-5V : C3749 - Video selector IC (U3703) flaw.
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player operating instructions. (7) When you use a DENON BD/DVD player, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-DENON BD/ DVD player, proceed to "YES".
Page 109
Check TV Use an HDCP-compatible TV. PC TVs cannot (11) Is the TV HDCP-compatible? be used. If the TV is not compatible with resolutions of (12) Is the TV compatible with resolutions of 1080P? 1080P, no picture will be output, even if the BD/DVD player resolution is set to 1080P.
4. AUDIO 4.1. AUDIO CHECK Audio output NG. Refer to "Audio Check PATH" (117 page). CHECK1 INPUT SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH ANALOG DIRECT CHECK2 INPUT SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 111
4.2. Power AMP (8U-110130-10) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. DHCT-C3 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
Page 112
4.3. Analog audio No sound is output Is the voltage of ±7V supplied to The power supply of ±7V is repaired. A POWER B'D N3902 1-3pin? Is the audio signal transmitted to The power amplifier is repaired. AMP CONNECT B'D N9002,N9016? Connect the connectors properly.
5. Network/USB 5.1. Cannot connect to network Only connect the set with the router by using a single cable for check. Checking the environment Check the LAN cable properly then turn the Is the LAN cable properly connected? power back on. Checking the settings Set the IP address and other parameters properly.
Page 114
It is not connected through a specific port. A part between U702-N701 on the 8U- Is the set connected to the network by connecting the LAN cable to 310115-2 board has poor soldering or is any of the ports? defective. It is not connected through all port.
Page 115
5.2. USB device is not recognized Checking the settings Are the USB port settings correct? Set the front and rear properly. Checking the USB device Are you using a USB hub? Don't use the USB hub. Only mass storage devices in FAT16 or FAT32 formats or MTPcompatible devices Is the USB device compatible with the set? and iPod (except some models) are supported.
Page 116
5.3. No picture or sound is output Checking the set (AVR-4520):(If no picture is output) Are video signals output from U607 pin 27 (Y) and pin 24 (C)? U607 and surrounding circuitry is defective. Check the analog video circuit. Checking the set (AVR-4520):(If no sound is output) Are S/PDIF signals output to N605 pin 7? U503 and surrounding circuitry is defective.
Page 117
5.4. MHL No picture or sound is output. The MHL cable is defective. (1) Check if the MHL cable is detected. Q804, Q805 and surrounding circuitry (8U- When the MHL cable is connected, can "High” be seen for 4pin on N1101 (8U-310116)? 310115-3) are defective.
Page 118
Timing waveform illustration from the start of MHL3.3V to when reset is released : Check items (4) MHL3.3V 337ms FRONT_RESET Controlled waveform(I2C), when power is turned on : Check items (5) DATA DDC waveform : Check items (6 DDC_CLK DDC_DATA...
6. SMPS DC 5V is not output. Replace the U6502(TOP256YN) and Is there damage in U6502 (TOP256YN)? D6503. Is there the damage in D9001/D9002/ Is the fuse (F70) blown? Replace the parts of damage. D6503? Is there solder short circuit in the PWB The solder short part of the PWB board board? is repaired.
Page 120
Operation waveform for each part Primary drain (Caution: High voltage, electric shock) After primary side rectification (Caution: High voltage, electric shock) 0.01/250 C6512 After secondary rectifications L6501 R6511 2.2M (2.2M) Z6513 L6507 3X8_CBS-B L.FILTER(LF2628NP-R273) D6503 BEADS D3SB60 R6512 Z6514 Z6503 L6504 3X8_CBS-B RADIATOR...
ZONE2 CVBS VIDEO LAN8720 SIGNAL OUT CVBS SIGNAL IN ETHERNET UART U706 DM860A U503 CVBS SELE SIGNAL OUT CTOR Network AudioOut EEPROM (SPDIF) iPod (for Backup) Authenticati (R1EX24256B) Network AudioOut (I2S) VIDEO ENC Network SAA7121 VideoOut DENON confidential D & M...
8U-110130-11 L_AMP_CONNECT_UNIT Z9003 OPEN Z9005 STYLE-PIN Z9007 OPEN Z9009 GN D OPEN TO N3201 GN D To_8U-210119-1_(N3201) GN D A.AUDIO/VIDEO_UNIT(2/4) GN D To_8U-110130-1_(N9032) To_8U-110130-2_(N9034) To_8U-110130-3_(N9033) To_8U-110130-4_(N9031) To_8U-110130-5_(N9030 GN D P.AMP(FL)UNIT P.AMP(C)UNIT P.AMP(SL)UNIT P.AMP(SBL)UNIT P.AMP(FHL)UNIT N9002 N9002 IDDLE- IDDLE - IDDLE- IDDLE- IDDLE - 10P-PHs...
N4009 4P-PH 8U-210119-4 Z400 4 STYLE-PIN CONNECT-2_UNIT Z4005 STYLE-PIN TO N1805 TO N1803 TO N1804 N4003 N4003 Z4006 33P-PLUG(C125Z1) STYLE-PIN TO N1806 To_8U-310116_(N1804) To_8U-310116_(N1805 To_8U-310116_(N1803) To_8U-310116_(N1806) TO DIGITAL TO DIGITAL TO DIGITAL DIGITAL_UNIT(11/4) N4002 N4002 DIGITAL_UNIT(11/4) DIGITAL_UNIT(11/4) DIGITAL_UNIT(11/4) B4001 B4002 N4001 N4001 M3-SIDE...
TO DIGITAL CONNECT DSP3.3V DGND TO 8U-310115-1(2/5 DA_POWER DA_POWER DSP3.3V DSP1.1V DSP1.1V DSP1.1V DSP1 DGND TO 8U-310115-1(3/5) BLM21PG221 20 PVIN VOUT BLM21PG221 DSP3.3V 21 PVIN VOUT DSP1.1V DSP2 22 NC DGND TO 8U-310115-1(4/5) 23 NC EX3AV OPEN BLM21PG221 24 NC NC(SW) 25 PGND NC(SW)
Page 160
DA_POWER DSP3.3V BLM21PG221 BLM21PG221 100P-IMSA-9832S-100Y DGND To_8U-310116_(N321) DIGITAL_UNIT(3/14) 8U-310115-1 DSP_UNIT(2/5) TO DSP2 TO DSP3 TO DSP1 TO 8U-310115-1(4/5) TO 8U-310115-1(5/5) TO 8U-310115-1(3/5) TO AM TO AO TO AI TO AK TO AQ TO AS SCHEMATIC DIAGRAMS (15/36) NETWORK/DSP UNIT (2/9) AUDIO SIGNAL LINE POWER + POWER -...
TO AP TO AN TO DSP CONNECT TO DSP CONNECT TO 8U-310115-1(2/5) TO 8U-310115-1(2/5) D1.1V D3.3V U202 C289 1000P PMS308416BTR-6C N C290 0. 1 1000P C291 DSP2D0 DSP2D1 5 DQ15 C292 0. 1 VDDQ VSSQ C293 1000P DSP2D14 DSP2D1 DQ14 DSP2D13 DSP2D2 DQ13...
TO AU TO AW TO 8U-310115-2(1/3) N606 N607 33P-SOCKET(C125Z2) 23P-SOCKET(C125Z2) N605 N608 N605 N608 33P-PLUG(C125Z1) 33P-PLUG(C125Z1) 860_V 860_V DACGND R660 OPEN DGND Z2_LINEL R661 OPEN 860_SY 860_S Y Z2_LINER C651 OPEN DGND DACGND R633 C655 860_SC R662 860_S C Z3_LINEL OPEN OPEN R663...
TO BA TO AZ TO N4008 TO 8U-310115/2(2/3) TO 8U-310115/2(1/3) N702-2 N702 To_8U-210119-7_(N4008) 19P-SOCKET(C125Z2) BRIDGE_UNIT R769 1.5K R750 OPEN R787 R751 OPEN R786 U704 S558-5999-U-7-F L712 DLW21SN900SQ2 4.7u C749 C753 MIIMDIO. VDD1A MDIO 860TX N R789 MIIRXD V CRS_DV/MODE2 U706 33x4 860TX P R789...
TO BF TO BH TO EE TO AUDIOPLD TO SUBCPU TO 8U-310116(2/14) DIGITAL MAIN TO 8U-310116(14/14) CONNECT TO 8U-310116(11/14) TO 8U-310116(13/14) DAC3.3V2 DA+5V C162 DACGND DACGND C123 1000P MAINDIRAUDIO C124 1000P U142 MAINDIRERR DIR_XIN NJM2115M C150 C159 R144 R146 10/16 C157 4.7u R130...
TO BQ TO CB TO AUDIO PLD TO SUB CPU TO 8U-310116(2/14) TO 8U-310116(14/14) DA3.3V DGND TO AUDIO PLD TO 8U-310116(2/14) TO BS SCHEMATIC DIAGRAMS (25/36) DIGITAL UNIT (3/14) AUDIO SIGNAL LINE POWER + POWER - STBY POWER...
TO GY TO DA TO GW TO HDMI TX TO HDMI TX TO HDMI TX TO 8U-310116(8/14) TO 8U-310116(8/14) TO 8U-310116(8/14) R1612 R1614 OPEN OPEN 1 A2 2 A3 1 A2 2 A3 7 A8 8 A9 7 A8 8 A9 DDR_1.8V DDR_1.8V DDR_1.8V...
TO DW TO DM TO_HDMI TO DIGITAL CONNECT TO RESET/SUPPLY SUBCPU HDMITX CONNECT TO 8U-310116(14/14) TO 8U-310116(8/14) TO 8U-310116(10/14) TO 8U-310116(11/14) TO 8U-310116(12/14 R2024 DGND DGND DGND GREENLED GREENLED C2017 FRONT_RST R2049 OPEN FRONT_RST FRONT_NO_FIL FRONT_NO_FIL U2002 R1EX24256BSAS0A SWM3.3V FL_CLK FLCLK 8 VCC MBSW3.3V...
TO DQ TO DG TO BG TO BW TO DY TO EB TO DU TO CE TO CA TO DE DIGITAL HDMI TO MAIN DAC TO DIR/ADC TO AUDIO PLD TO_DSP_CONNECT TO_HDMI_RX TO_MAIN_CPU TO_HDMI_TX CONNECT CONNECT TO RESET/SUPPLY TO 8U-310116(1/14) TO 8U-310116(2/14) TO 8U-310116(4/14) TO 8U-310116(3/14)
EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
PARTS LIST OF EXPLODED VIEW z Parts indicated by "nsp" on this table cannot be supplied. z P.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts.
Page 185
PWB BRACKET (A.REG) 44431029400AD FRONT PANEL 40231022100AD FRONT PANEL BKE2 40231022101AD FRONT PANEL 40231022102AD SPE2 FRONT PANEL 40231022103AD FRONT PANEL 40231022104AD DENON BADGE 42141002300AD DENON BADGE 42141002301AD INNER PANEL 44351005300AD INNER PANEL 44351005301AD LENS LENS 48151002500AD 41651007400AD WINDOW 42251004300AD DOOR SHEET...
Page 186
Ref. No. Part No. Part Name Remarks Q'ty New DOOR SUB PANEL 41751001900AD DOOR SUB PANEL 41751001901AD 457010003008M MAGNET DOOR SR7005 A332 EARTH PLATE DOOR 44631006300AD DOOR PLATE 44631006700AD 00D4210763010 GEAR DAMPER FRONT CHASSIS 44531013600AD FFC HOLDER (FLD) 44551013900AD FFC HOLDER (HDMI) 44551013700AD KNOB RING (M) 42451002900AD...
Page 187
Ref. No. Part No. Part Name Remarks Q'ty New SCREW CHASSIS + BACK PANEL 00M51270310U0 SCREW PWB ASSY + TRANS PLATE 00M51270310U0 SCREW AL PLATE + CHASSIS 00M51270310U0 00M51270310U0 SCREW SMPS COVER + CHASSIS SCREW RADIATOR BRACKET L/R 00M51270310U0 SCREW PWB BRACKET (A.REG) 00M51270310U0 SCREW RADIATOR BRACKET L/R 00M51270310U0...
PACKING VIEW U10 U20 U25 U30 U40 U120 U110 U130 U130 PARTS LIST OF PACKING & ACCESSORIES z Parts indicated by "nsp" on this table cannot be supplied. z Parts indicated by the " ★ " mark are not illustrated in the exploded view. z The parts listed below are only for maintenance.
Page 189
GETTING STARTED (E2) SPE2 S.S.LIST(EX) BKE2 S.S.LIST(EX) CIBKE3 SERVICE STATION LIST S.S.LIST(EX) SPE1C S.S.LIST(EX) SPE2 GUARANTEE(S)SUB ASSY WARRANTY FOR CHINA DENON SPE1C CIBKE3 11601001400AS AM ANTENNA(ANTA12G) FM ANT ASSY BKE2 11601001100AS CIBKE3 FM ANT ASSY 11601001100AS FM ANT ASSY 11601001100AS...
SEMICONDUCTORS Only major semiconductors are shown. General semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. 1. IC's R5F56108VNFP (DIGITAL : U2001) PE0/D8 PC4/A20 PD7/D7 PC5/A21/SCK5/CS5#-D PD6/D6 PC6/A22/RxD5/CS6#-D PD5/D5 PC7/A23/TxD5/CS4#-D/CS7#-D PD4/D4...
Page 191
R5F56108VNFP Terminal Functions Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY TDI/TXD P04/IRQ12-A/TMCI3/ E20 Emulator control signal/Mitsubishi MITSUBISHI/ I/O/I M3VPu -/-/I -/-/I TxD4/TDI Programer/Nomal:Input NC(NORMRAL) P03/IRQ11-A/TMRI3/ TMS/ M3VPu E20 Emulator control signal/Nomal:Input NC(NORMRAL) SCK4/TMS USB SEL USB control pin P67/DA1 USB EN USB control pin...
Page 192
64 P51/WR1#/BC1# ZVOLSTB ZONE VOL. Control pin (NJW1194) 65 P50/WR0#/WR# 66 P77 67 P76/IRQ14-A TU GPO2_INT TUNER GPIO2 input pin SUB UPDATEmode control(DPMS/DENON SUB UPDATE WRITTER)."L". SUB Program mode 68 P75 "H",then SUB RST. MAIN-SUB CPU Communication control PC7/A23/CS4#-D/ MOSI...
Page 193
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY PB3/A11/PO27/ TIOCC9/TIOCD9 PB2/A10/PO26/ TIOCC9 PB1/A9/PO25/TIOCA9/ V FANDET M3VPu TIOCB9 V FANCONT ON 86 P74/ADTRG3# AEXP OE EXPANDER control pin(AUDIO MUTE) 87 P73 AEXP CLK EXPANDER control pin(AUDIO MUTE) 88 P72 P71/CS4#-C/CS5#-C/ AEXP DATA EXPANDER control pin(AUDIO MUTE)
Page 194
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY MAIN CPU POWER control pin(POWER 128 P92/AN10 CPU POWER ON:"H",CEC ON STANDBY:"H") 129 P91/AN9 AMPSIGDET AMP signal detection pin 130 VSS 131 P90/AN8 MODE Destination detection pin 132 VCC +3.3V 133 P47/IRQ15-B/AN7 MIC DET...
Page 196
18 P82/INT0 19 P81 20 P80/(RXD5) 21 P77/(CLK5) SUB TDO PLD rewriting control (JTAG) A PLD control pin/ DENON WRITTER/ MITSUBISHI rewritten 22 P76/(TXD5) A PLD CS /"D/M" for determining (DW :L) A PLD DATA A PLD control pin 23 P75...
Page 197
Pin Name Symbol I/O Type Pu/Pd STBY Function STBY1 STBY2 STBY3 62 VSS 63 P27 DAC RST1 DAC control pin(PCM1795) DIGITAL VIDEO power control pin (DV5V,DV3.3V) 64 P26 DV POWER1 NPN Tr 65 P25/INT7 ADV7850 INT1 CEC3VPu HDMI ADV7850 INT output 66 P24/INT6 ADV7850 INT2 CEC3VPu...
Page 198
MC14094B MC14094BDTR2G (A.AUDIO/VIDEO : U3001, U3002, U3003, U3004) PIN ASSIGNMENT STROBE OUTPUT DATA ENABLE CLOCK Q′ TRUTH TABLE Parallel Outputs Serial Outputs Output Enable Q′ Clock Strobe Data No Chg. No Chg. No Chg. No Chg. No Chg. −1 No Chg. −1 No Chg.
Page 199
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15220FP (A.AUDIO/VIDEO : U3201, U3202) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB...
Page 200
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15220FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
Page 201
G G I I I I BLOCK DIAGRAM NJW1194A (A.AUDIO/VIDEO : U3203, U3204) H27U1G8F2B Series 1 Gbit (128 M x 8 bit) NAND Flash ...
Page 203
SAA7121 (NETWORK/DSP : U0607) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SAA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3...
Page 204
Digital Video Encoder (ConDENC) SAA7120; SAA7121 SAA7121 Pin Description PINNING SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1...
Page 205
Chapter 2 Pin Description and Configuration LAN8720A (NETWORK/DSP : U0706) VDD1A MDIO SMSC CRS_DV/MODE2 LAN8720A/LAN8720Ai 24 PIN QFN (TOP VIEW) RXER/PHYAD0 VDDIO RXD0/MODE0 RBIAS RXD1/MODE1 NOTE: Exposed pad (VSS) on bottom of package must be connected to ground Figure 2.1 24-QFN Pin Assignments (TOP VIEW) Note: When a lower case “n”...
Page 206
Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support Datasheet Pin Assignments LAN8720A Pin Function Table 2.8 24-QFN Package Pin Assignments PIN NUM PIN NAME PIN NUM PIN NAME VDD2A LED2/nINTSEL nINT/REFCLKO Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support LED1/REGOFF Datasheet nRST...
Page 207
Sil1292CNUC (NETWORK/DSP : U0802) AVDD12 RSVDL1 TXC- VDD12 TXC+ RSVDL2 TX0- RESET# SiI 1292 TX0+ PWR5V_DET (Top View) TX1- INT# DSDA TX1+ TX2- DSCL The ePad must be grounded TX2+ CBUS/HPD VDD5_IN HPD_IN Sil1292CNUC Block diagram 1.8 V Reg 3.3 V Reg VREG33_OUT VDD5_IN RESET#...
Page 208
ADSP21487KSWZ4B (NETWORK/DSP : U0101, U0201, U0301) PIN 1 GND PAD (PIN 177) at BOTTOM Preliminary Technical Data ADSP-21483/21486/21487/21488/21489 TOP VIEW (PINS DOWN) 176-LEAD LQFP_EP LEAD ASSIGNMENT ADSP21487KSWZ4B Terminal Function Table 53. 176-Lead LQFP_EP Lead Assignment Pin Name Pin No. Pin Name Pin No.
Page 210
LC89057W-VF4A (DI: IC101) LC89057W-VF4A (DI: IC101) LC89057W-VF4A (DIGITAL : U0103, U0104) EMPHA/UO AUDIO/VO XMODE EMPHA/UO AUDIO/VO XMODE RX OUT Microcontroller C bit, U bit 37 DO RX OUT Microcontroller C bit, U bit 37 DO 36 RERR 24 SDIN 36 RERR 23 SLRCK 24 SDIN Input Demodulation Data 22 SBCK...
Page 211
Pin Name Function XOUT X tal osc. connecting output terminal X tal osc. connection, external clock input terminal (24.576MHz or 12.288MHz) DVDD Digital power DGND Digital GND EMPHA/UO Emphasis information/U-data output/Chip address setting terminal AUDIO/VO Non-PCM detect/V-flag output/Chip address setting terminal CKST Clocwitch transition period output/Demodulation master or slave function switching terminal Interrupt output for µcom (Interrupt factor selectable)/Modulation or general I/O switching terminal RERR PLL lock error, data error flag output µcom I/F, read out data output terminal (3-state) µcom I/F, write data input terminal µcom I/F, chip enable input terminal µcom I/F, clock input terminal XMODE System reset input terminal DGND Digital GND DVDD Digital power TMCK/PIO0 256fs system clock input for modulation/General I/O in/output terminal TBCK/PIO1 64fs bit clock input for modulation/General I/O in/output terminal TLRCK/PIO2 fs clock input for modulation/General I/O in/output terminal TDATA/PIO3 Serial audio data input for modulation/General I/O in/output terminal TXO/PIOEN Modulation data output/ General I/O enable input terminal * For latch-up countermeasure, perform each power supply ON/OFF in the same timing.
Page 212
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100PWR (DIGITAL : U0106) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME Charge pump power supply, 3.3V CPVDD CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM...
Page 214
SLES248 – MAY 2009 www.ti.com ........................................PIN CONFIGURATION DB PACKAGE SSOP-28 PCM1795 (DIGITAL : U0403, U0404, U0405, U0406, U0407, U0408, U0409) (TOP VIEW) V 2L ZEROL ZEROR AGND3L MSEL LRCK DATA AGND2 DGND AGND1 AGND3R V 2R Table 1. TERMINAL FUNCTIONS TERMINAL NAME DESCRIPTION...
Page 215
PCM1795 SLES248 – MAY 2009 ........................................www.ti.com Table 1. TERMINAL FUNCTIONS (continued) TERMINAL NAME DESCRIPTION System clock input — Analog power supply, 5 V — Analog power supply (left channel DACFF), 5 V — Analog power supply (right channel DACFF), 5 V —...
Page 219
Pin No. Mnemonic Description Ground Ground Ground RXB_2+ Digital Input Channel 2 true of Port B in the HDMI interface. RXB_1+ Digital Input Channel 1 true of Port B in the HDMI interface. RXB_0+ Digital Input Channel 0 true of Port B in the HDMI interface. RXB_C+ Digital input clock true of Port B in the HDMI interface.
Page 220
ADV7850 Pin No. Mnemonic Description TVDD HDMI termination supply (3.3V) TVDD HDMI termination supply (3.3V) TVDD HDMI termination supply (3.3V) Ground Ground ACMUXIN_1R Audio Codec Mux Input 1 Right Channel ACMUXIN_1L Audio Codec Mux Input 1 Left Channel RXA_0+ Digital Input Channel 0 true of Port A in the HDMI interface. RXA_0- Digital Input Channel 0 complement of Port A in the HDMI interface.
Page 221
Pin No. Mnemonic Description ACMUXIN_5L Audio Codec Mux Input 5 Left Channel EP_MISO External EDID EEPROM interface EP_MOSI External EDID EEPROM interface SPDIF_IN S/PDIF digital audio input for Audio Return Channel (ARC). RXA_5V 5V detect pin for Port A in the HDMI interface. Ground Ground Ground...
Page 223
Pin No. Mnemonic Description Ground Ground Ground Ground Ground Ground Ground TTX_SCLK VBI data interface TTX_MOSI VBI data interface TTX_MISO VBI data interface TTX_CSB VBI data interface Video Digital supply (1.8V) Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground...
Page 224
ADV7850 Pin No. Mnemonic Description TX_2+ Digital Output Channel 2 true of the HDMI Tx. TX_2- Digital Output Channel 2 complement of the HDMI Tx. Ground TX_DDC_SDA Serial data for DDC bus of HDMI Tx. TX_DDCA_SDA is 5 V tolerant. AVDD Video Analog supply voltage (1.8V) AVDD...
Page 225
Pin No. Mnemonic Description trilevel/bilevel input on the SCART or D-terminal connector. AA23 VS_IN2/TRI6 The VS input signal is used for 5-wire timing mode. This ball can also be used as a trilevel/bilevel input on the SCART or D-terminal connector. Ground TX_PVDD HDMI Tx digital supply (1.8V)
Page 227
ADV8003 Pin No. Mnemonic Type Description OSD_IN[23]/EXT_DIN[7] OSD video input/ External OSD Video Pixel Input Port (OSD_IN[23])/Additional TTL Input for miscellaneous digital External CCIR 656 Video Data (EXT_DIN[7]). OSD_DE OSD video sync Data Enable for the OSD Input Port. OSD_CLK/EXT_CLK OSD video sync Pixel Clock for the OSD Input Port (OSD_CLK)/Pixel Clock for External Video Data (EXT_CLK).
Page 228
ADV8003 Pin No. Mnemonic Type Description OSD_IN[19]/EXT_DIN[3] OSD video input/ External OSD Video Pixel Input Port (OSD_IN[19])/Additional TTL Input for miscellaneous digital External CCIR 656 Video Data (EXT_DIN[3]). OSD_IN[20]/EXT_DIN[4] OSD video input/ External OSD Video Pixel Input Port (OSD_IN[20])/Additional TTL Input for miscellaneous digital External CCIR 656 Video Data (EXT_DIN[4]).
Page 229
ADV8003 Pin No. Mnemonic Type Description DAC1 Analog video output Encoder DAC1 Output. DAC2 Analog video output Encoder DAC2 Output. OSD_IN[13]/VBI_SCK OSD video input/ External OSD Video Pixel Input Port (OSD_IN[13])/Serial Clock for VBI Data miscellaneous digital Serial Port (VBI_SCK). OSD_IN[14]/VBI_MOSI OSD video input/ External OSD Video Pixel Input Port (OSD_IN[14])/Master Out Slave In for VBI...
Page 230
ADV8003 Pin No. Mnemonic Type Description Ground. Ground. Ground. Ground. Ground. Ground. TX1_2+ HDMI Tx1 HDMI1 Channel 2 True Output. TX1_2− HDMI Tx1 HDMI1 Channel 2 Complementary Output. Digital video sync Data Enable for Digital Input Video. Digital video sync Horizontal Sync for Digital Input Video.
Page 231
ADV8003 Pin No. Mnemonic Type Description DVDD Power Digital Power Supply (1.8 V). Ground. Ground. Ground. Ground. Ground. Ground. Ground. Ground. Ground. Ground. HPD_TX1 HDMI Tx1 Hot Plug Assert Signal Input for HDMI Tx1. Ground. TX1_C+ HDMI Tx1 HDMI1 Clock True Output. TX1_C−...
Page 232
ADV8003 Pin No. Mnemonic Type Description CEC2 HDMI Tx2 HDMI Tx2 Consumer Electronics Control (CEC). PVDD5 Power HDMI Tx PLL Power Supply (1.8 V). This pin is a voltage regulator output. Connect a decoupling capacitor between this pin and ground. AVDD3 Power HDMI Analog Power Supply (1.8 V).
Page 233
ADV8003 Pin No. Mnemonic Type Description Ground. Ground. Ground. Ground. Ground. Ground. Ground. Ground. HPD_TX2 HDMI Tx2 Hot Plug Assert Signal Input for HDMI Tx2. Ground. TX2_0+ HDMI Tx2 HDMI2 Channel 0 True Output. TX2_0− HDMI Tx2 HDMI2 Channel 0 Complementary Output. P[10] Digital video input Digital Video Input Bus[35:0].
Page 234
ADV8003 Pin No. Mnemonic Type Description DDR_DQS[2] DDR interface Data Strobe for DDR Data Byte[23:16]. Ground. DDR_DQ[23] DDR interface Data Line. Interface to external RAM data lines. DVDD_DDR Power DDR Interface Supply (1.8 V). DDR_DQS[3] DDR interface Data Strobe for DDR Data Byte[31:24]. Ground.
Page 235
ADV8003 Pin No. Mnemonic Type Description DDR_DQ[29] DDR interface Data Line. Interface to external RAM data lines. DDR_A[12] DDR interface Address Line. Interface to external RAM address lines. AB10 DDR_A[6] DDR interface Address Line. Interface to external RAM address lines. AB11 DDR_A[3] DDR interface...
PARTS LIST OF P.W.B. UNIT z Parts indicated by "nsp" on this table cannot be supplied. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...