Denon AVR-4520CI Owner's Manual page 133

Setting items
Video Output Auto(Dual) : The presence of a TV connected to the HDMI MONITOR 1
Make settings for HDMI or HDMI MONITOR 2 connector is detected automatically, and that TV
monitor output. connection is used.
Monitor 1 : A TV connected to the HDMI MONITOR 1 connector is always
used. Video is not output from the TV connected to the HDMI MONITOR
2 connector.
Monitor 2 : A TV connected to the HDMI MONITOR 2 connector is always
used. Video is not output from the TV connected to the HDMI MONITOR
1 connector.
• If both the HDMI MONITOR 1 and HDMI MONITOR 2 connectors are
connected and "Resolution" (vpage 132) is set to "Auto", the signals
are output with a resolution compatible with both TV.
• With "Resolution"
the TV you are using is compatible with the resolution under "Video" –
"HDMI Monitor 1" or "HDMI Monitor 2" (vpage 153).
NOTE
Depending on the monitor you have connected, the display may not
be correct when you set to "Auto(Dual)". In such a case, set to either
"Monitor 1" or "Monitor 2".
On : Stretches video signals vertically.
Vertical Stretch
Sets whether video signals Off : Does not stretch video signals vertically.
are vertically stretched or
"Vertical Stretch" can be set when "i/p Scaler" is set to anything
not.
other than "Off".
HDMI Pass Through On : Passes the selected HDMI input through the AV receiver's HDMI
Selects how the AVR will output when the AV receiver is in standby power mode.
pass HDMI signals to the Off : No HDMI signals are passed through the AV receiver's HDMI output
HDMI output in standby in standby power mode.
power mode.
NOTE
When "HDMI Pass Through" is set to "On", it consumes more
standby power. If you are not using this unit for an extended period, it
is recommended that you unplug the power cord from the power outlet.
DVD
Setting details
(vpage 132) not set to "Auto", check whether
Setting items
HDMI Control On : Use HDMI control function.
You can link operations with Off : Do not use HDMI control function.
devices connected to HDMI
and compatible with HDMI
• When a device that is not compatible with the HDMI control function is
Control.
connected, set "HDMI Control" to "Off".
• Please consult the operating instructions for each connected device to
check the settings.
• Refer to "HDMI control function"
about the HDMI control function.
NOTE
• When "HDMI Control" is set to "On", it consumes more standby
power. If you are not using this unit for an extended period, it is
recommended that you unplug the power cord from the power outlet.
• The HDMI control function controls operations of a TV that is compatible
with the HDMI control function. Make sure that the TV and HDMI are
connected when you perform HDMI control.
• If the "HDMI Control" settings have been changed, always reset the
power to connected devices after the change.
Pass Through Source Last : Choose this option to "pass through" the last used HDMI input
The AVR will "pass video source.
through" the sources CBL/SAT / DVD / Blu-ray / GAME / AUX1 / AUX2 / MEDIA PLAYER / CD /
HDMI video signal when in TV AUDIO : Choose one of these HDMI sources to be passed through
standby. when the AVR is in standby.
"Pass Through Source" can be set when "HDMI Control" is set to
"On" or "HDMI Pass Through" is set to "On".
Control Monitor Monitor 1 : Uses the HDMI Monitor 1 for HDMI control.
Selects the HDMI monitor Monitor 2 : Uses the HDMI Monitor 2 for HDMI control.
for which you want to ZONE4 : Uses the HDMI monitor in ZONE4 for HDMI control.
enable the HDMI control
function.
• "Control Monitor" can be set when "HDMI Control" is set to "On".
• The ARC function only works for either the HDMI Monitor 1 or HDMI
Monitor 2 connector that is specified in "Control Monitor".
130
Video
Setting details
(vpage 102) for more information
v See overleaf