Denon AVR-4520CI Owner's Manual page 148

Setting items
Impedance 8Ω/ohms : Select when the impedance per speaker for all the connected
Set the impedance of speakers is 8Ω or larger.
connected speakers. 6Ω/ohms : Select when the impedance for any of the connected speakers
is between 6Ω and 8Ω.
4Ω/ohms : Select when the impedance for any of the connected speakers
is between 4Ω and 8Ω.
Check the speaker impedance (Ω) shown on the back of your speakers
or in the instruction manual beforehand.
Front Speaker 2ch Playback : The front speakers used in direct play (2 channel), stereo
Set the front speakers to play and pure direct play (2 channel) are set in advance.
use for every sound mode. • A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Multi ch Playback : The front speakers used in play modes other than
direct play (2 channel), stereo play and pure direct play (2 channel) are set
in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
This can be set when "Assign Mode" (vpage 141) is set to "7.1ch
+ Front B".
2ch Playback Setting : Select the method for setting the speakers used in the 2-channel
Select the method for direct and stereo playback modes.
setting the speakers used • Auto : The settings at "Speakers" (vpage 139) are applied.
in the 2-channel direct and • Manual : Make separate settings for 2-channel. Make the following
stereo playback modes. settings:
Front : Set the front speaker size.
• Large : Use a large speaker that can adequately play back low
frequencies.
• Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Config." – "Subwoofer" (vpage 142) is set to "None",
the setting is automatically set to "Large".
DVD
Setting details
145
Setting items
2ch Playback Subwoofer : Set the presence of a subwoofer.
(Continued) • Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Config." – "Subwoofer" (vpage 142) is set to "None",
the setting is automatically set to "No". If the "Front" setting is
"Small", the setting is automatically "Yes".
SW Mode : Select low range signals to be reproduced by subwoofer.
• LFE : When the "2ch Playback – "Front" setting is set to "Large", the
LFE signal alone is output from the subwoofer. Also, when the "2ch
Playback" – "Front" setting is set to "Small", the front channel low
range signal is added to the LFE signal output from the subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made "2ch Playback" – "Subwoofer" is set to
"Yes".
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This setting can be set made "2ch Playback" – "Subwoofer" is set to
"Yes".
• If the "2ch Playback" – "Front" setting is "Large" and the "SW Mode"
setting is "LFE", "Full Band" is displayed and the setting cannot be
made.
Distance FL / Distance FR : Select speaker for distance setting.
• 0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set distance from
main listening point to speaker.
Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
Level FL / Level FR : Select speaker for level adjustment.
• –12dB – +12dB (0dB) : Adjust the level of each channel.
Speakers
Setting details