Table of Contents
Advertisement
7) Replenish oil until oil level is brought to FULL level
mark on dipstick.
Engine oil specifications
: About 5.1 liters (9.0 lmp pt.)
The filler inlet is at the top of the cylinder head cover.
Use only synthetic engine oil of specified grade
below.
Vehicle with diesel particulate filter:
ACEA C3
Vehicle without diesel particulate filter:
ACEA C3 or B4
Select the appropriate oil viscosity according to the
chart [A].
It is highly recommended to use SAE 5W-30 oil.
NOTE
Note that the amount of oil required when
actually changing oil may somewhat differ
from the data depending on various
conditions (temperature, viscosity, etc.)
Proper engine oil viscosity chart
[A]
0W-30
o
-30
-20
-10
C
o
-22
F
-4
14
8) Check oil filter and drain plug for oil leakage.
9) Check oil level as follows.
a) Warm up engine to normal operating
temperature.
b) Stop engine and wait 10 min.
c) Remove dipstick and wipe oil off it with a clean
lint-free cloth.
d) Screw in dipstick (cap) fully.
e) Remove dipstick again and check oil level.
Add oil, as necessary, to bring oil level to FULL
level mark (1) on dipstick.
2. Low level mark
5W-40
5W-30
0
10
20
30
40
32
50
68
86
104
I6JB0A020005-02
1
2
I5JB0B020008-01
Maintenance and Lubrication:
Engine Coolant Change
WARNING
!
To help avoid danger of being burned, do not
remove radiator cap while engine and
radiator are still hot. Scalding fluid and steam
can be blown out under pressure if cap is
taken off too soon.
Change engine coolant referring to "Cooling System
Flush and Refill: For Petrol Engine Model in Section 1F"
or "Cooling System Refilling: For Diesel Engine Model in
Section 1F".
Exhaust system Inspection
WARNING
!
To avoid danger of being burned, do not
touch exhaust system when it is still hot. Any
service on exhaust system should be
performed when it is cool.
Check exhaust system for loose, damage, leakage, etc.
referring to "Exhaust System Check: For Petrol Engine
Model in Section 1K" or "Exhaust System Check: For
Diesel Engine Model in Section 1K".
Spark Plugs Replacement
Replace spark plugs with new ones referring to "Spark
Plug Removal and Installation: For Petrol Engine Model
in Section 1H".
Air Cleaner Filter Inspection
Check that filter is not excessively dirty, damaged or oily
and clean filter with compressed air from air outlet side
of filter.
Refer to "Air Cleaner Filter Inspection and Cleaning: For
M16A Engine with VVT in Section 1D", "Air Cleaner
Filter Inspection and Cleaning: For J20 Engine in
Section 1D" or "Air Cleaner Filter Inspection and
Cleaning: For F9Q Engine in Section 1D".
Air Cleaner Filter Replacement
Replace air cleaner filter with new one referring to "Air
Cleaner Filter Removal and Installation: For M16A
Engine with VVT in Section 1D", "Air Cleaner Filter
Removal and Installation: For J20 Engine in Section 1D"
or "Air Cleaner Filter Removal and Installation: For F9Q
Engine in Section 1D".
Fuel Lines and Connections Inspection
Visually inspect fuel lines and connections for evidence
of fuel leakage, hose cracking and damage. Make sure
all clamps are secure.
Repair leaky joints, if any.
Replace hoses that are suspected of being cracked.
0B-10
S6JB0A0206005
S6JB0A0206006
S6JB0A0206007
S6JB0A0206008
S6JB0A0206009
S6JB0A0206010
Advertisement
Chapters
Table of Contents
