Extron electronics Quantum Ultra Series User Manual page 86

Command
IP Setup
NOTES:
•
Unless noted, all commands apply to LAN A.
•
After adjusting any IP setting, enter the network reboot command
Set unit name
24
NOTES:
•
Up to 15 characters are permitted. No blank or space characters are allowed. Names are not case sensitive.
•
The first character must be an alpha character (A-Z, a-z). The last character cannot be a hyphen.
View unit name
View hardware (MAC)
address for LAN A
View hardware (MAC)
address for LAN B
Set date and time
View date and time
Verbose Mode
Set verbose mode
View verbose mode
DHCP
After adjusting IP settings by the CI, CS, or CG commands, you must enter the network reboot command
NOTE:
E }
1BOOT for the command to take effect. This is not required if you use the CISG command.
Set DHCP to On
24
Set DHCP to Off
24
View DHCP mode
NOTE: Attempting to set the IP address, subnet mask, or gateway address while DHCP is on results in an E14 error.
KEY:
X1)
DHCP status: 1 = On, 0 = Off (default).
=
X11@
Unit name: Text string of up to 15 characters: A-Z, 0-9, and hyphen (-).
=
X11*
= Hardware (MAC) address (00-05-A6-xx-xx-xx)
X12@
Verbose mode: 0 = None (default for Telnet), 1 = Verbose mode on (default for RS-232 and USB), 2 = Verbose
=
mode off, tagged responses enabled for queries, 3 = Verbose mode and tagged responses for queries enabled
(see the Verbose mode symbol definitions
X12&
Set date and time format: MM/DD/YY-HH:MM:SS Example: 08/17/21-13:51:30
=
View date and time format:
Example: Tue, 17 Aug 2021 13:53:58
Quantum Ultra Series Videowall Processing Systems • Remote Configuration and Control
ASCII Command
(Host to Processor)
E X11@ }
CN
E }
CN
E }
1CH
E }
2CH
E X2& }
CT
E }
CT
E X12@ }
CV
E }
CV
E }
1DH
E }
0DH
E }
DH
on page 67).
Www
{day of the week},
Response
(Processor to Host)
E }
1BOOT
for the command to take effect.
X11@ ]
Ipn •
X11@]
In verbose modes 2 and 3:
X11@ ]
Ipn •
X11* ]
In verbose modes 2 and 3:
X11* ]
Iph 1 *
X11*]
In verbose modes 2 and 3:
X11*]
Iph 2 *
X12& ]
Ipt •
X12&]
X12@ ]
Vrb
X12@ ]
In verbose modes 2 and 3:
X12@ ]
Vrb
]
Idh 1
]
Idh 0
X1) ]
In verbose modes 2 and 3:
X1) ]
Idh
DD Mmm YYYY HH:MM:SS
• • •
Additional Description
Specify a name for the unit.
View the name of the unit.
View unit media access code
X11*
(MAC) address for the
LAN A port.
View unit media access code
X11*
(MAC) address for the
LAN B port.
X2&
Set local date and time .
X2&
View local date and time .
Set the verbose mode.
View current verbose mode
X12@
.
Enable Dynamic Host
Configuration Protocol (DHCP) to
enable automatic assigning of IP
addresses.
Disable DHCP automatic IP
address assignment.
View the DHCP status: On or
Off (default).
.
78