B4: Timer Function - YASKAWA GA800 Programming Manual

1.5 b: Application
No.
Name
(Hex.)
b3-35 Low Back EMF
Detection Level
(0BC3)
Expert
b3-36 High Back EMF
Detection Level
(0BC4)
Expert
b3-54 Search Time
(3123)
b3-55 Current Increment Time
(3124)
Expert
b3-56 InverseRotationSearch
WaitTime
(3126)
b3-61 Init Magnet Pole
Estimation Gain
(1B96)
Expert
◆

b4: Timer Function

No.
Name
(Hex.)
b4-01 Timer Function ON-
Delay Time
(01A3)
b4-02 Timer Function OFF-
Delay Time
(01A4)
b4-03 Terminal M1-M2 ON-
Delay Time
(0B30)
Expert
b4-04 Terminal M1-M2 OFF-
Delay Time
(0B31)
Expert
b4-05 Terminal M3-M4 ON-
Delay Time
(0B32)
Expert
b4-06 Terminal M3-M4 OFF-
Delay Time
(0B33)
Expert
b4-07 Terminal M5-M6 ON-
Delay Time
(0B34)
Expert
b4-08 Terminal M5-M6 OFF-
Delay Time
(0B35)
Expert
26
V/f CL-V/f OLV CLV AOLV
Sets the Low Back EMF Detection Level. Usually it is not necessary to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the voltage level for Speed Search restart. Usually it is not necessary to change this
setting.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that the drive will run Speed Search.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that the drive will increase the current from zero current to the
setting value of b3-06 [Speed Estimation Current Level 1].
V/f CL-V/f OLV CLV AOLV
Sets the wait time until the drive starts inverse rotation search after it completes forward
search when you do inverse rotation search during Current Detection Speed Search.
V/f CL-V/f OLV CLV AOLV
Adjusts the Initial Pole Detection response gain when A1-02 = 6 [Control Method
Selection = AOLV/PM]. Set b3-61 > 0.0 for a general IPM motor.
The drive sets this value automatically when High Frequency Injection Tuning completes
correctly.
Note:
• It is available when n8-35 = 1 [Initial Pole Detection Method = High Frequency
Injection].
• To adjust the Initial Pole Detection response gain when A1-02 = 5, 7 [OLV/PM, CLV/
PM], set n8-41 [HFI P Gain].
V/f CL-V/f OLV CLV AOLV
Sets the ON-delay time for the timer input.
V/f CL-V/f OLV CLV AOLV
Sets the OFF-delay time for the timer input.
V/f CL-V/f OLV CLV AOLV
Sets the delay time until the contact is turned ON after the function set with H2-01 turns
ON.
V/f CL-V/f OLV CLV AOLV
Sets the delay time to deactivate the contact after the function set in H2-01 deactivates.
V/f CL-V/f OLV CLV AOLV
Sets the delay time to activate the contact after the function set in H2-02 activates.
V/f CL-V/f OLV CLV AOLV
Sets the delay time to deactivate the contact after the function set in H2-02 deactivates.
V/f CL-V/f OLV CLV AOLV
Sets the delay time to activate the contact after the function set in H2-03 activates.
V/f CL-V/f OLV CLV AOLV
Sets the delay time to deactivate the contact after the function set in H2-03 deactivates.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
Default
Ref.
(Range)
10% 219
(5 - 50%)
0.970 219
(0.500 - 1.000)
400 ms 219
(10 - 2000 ms)
10 ms 219
(10 - 2000 ms)
Determined by o2-04 220
(0.1 - 5.0 s)
5.0 220
(-20.0 - +20.0)
Default
Ref.
(Range)
0.0 s 221
(0.0 - 3000.0 s)
0.0 s 221
(0.0 - 3000.0 s)
0 ms 221
(0 - 65000 ms)
0 ms 221
(0 - 65000 ms)
0 ms 221
(0 - 65000 ms)
0 ms 221
(0 - 65000 ms)
0 ms 222
(0 - 65000 ms)
0 ms 222
(0 - 65000 ms)