U5: Pid Monitors; U6: Operation Status Monitors - YASKAWA GA800 Programming Manual

◆

U5: PID Monitors

No.
Name
(Hex.)
U5-01 PID Feedback
(0057)
U5-02 PID Input
(0063)
U5-03 PID Output
(0064)
U5-04 PID Setpoint
(0065)
U5-05 PID DifferentialFdbk
(07D2)
U5-06 PID Fdbk-Diff PID Fdbk
(07D3)
U5-21 Energy Save Coeff Ki
(0872)
Expert
U5-22 Energy Save Coeff Kt
(0873)
Expert
U5-99 PID Setpoint Command
(1599)
◆

U6: Operation Status Monitors

No.
Name
(Hex.)
U6-01 Iq Secondary Current
(0051)
U6-02 Id ExcitationCurrent
(0052)
U6-03 ASR Input
(0054)
U6-04 ASR Output
(0055)
U6-05 OutputVoltageRef: Vq
(0059)
YASKAWA TOEPYAIGA8002B GA800 Drive Programming
V/f CL-V/f OLV CLV AOLV
Shows the PID control feedback value. Parameter b5-20 [PID Unit Selection] sets the display units.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the change between the PID setpoint and PID feedback (the quantity of PID input) as a
percentage of the maximum output frequency.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the PID control output as a percentage of the maximum output frequency.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the PID setpoint. Parameter b5-20 [PID Unit Selection] sets the display units.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the PID differential feedback value as a percentage of the maximum output frequency.
This monitor is available after you set H3-02, H3-10, or H3-06 = 16 [MFAI Function Selection =
Differential PID Feedback].
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the difference from calculating U5-05 - U5-01 [PID DifferentialFdbk] - [PID Feedback].
Unit: 0.01%
Note:
U5-01 [PID Feedback] = U5-06 when H3-02, H3-10, or H3-06 ≠ 16 [MFAI Function Selection ≠
Differential PID Feedback].
V/f CL-V/f OLV CLV AOLV
Shows the energy-saving coefficient Ki value for PM.
Unit: 0.01
V/f CL-V/f OLV CLV AOLV
Shows the energy-saving coefficient Kt value for PM.
Unit: 0.01
V/f CL-V/f OLV CLV AOLV
Shows the PID setpoint command. Parameter b5-20 [PID Unit Selection] sets the display units.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the value calculated for the motor secondary current (q axis) as a percentage of the motor
rated secondary current.
Unit: 0.1%
V/f CL-V/f OLV CLV AOLV
Shows the value calculated for the motor excitation current (d axis) as a percentage of the motor
rated secondary current.
Unit: 0.1%
V/f CL-V/f OLV CLV AOLV
Shows the ASR input value as a percentage of the maximum frequency.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the ASR output value as a percentage of the motor rated secondary current.
Unit: 0.01%
V/f CL-V/f OLV CLV AOLV
Shows the drive internal voltage reference for motor secondary current control (q axis).
Unit: 0.1 V
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
1.17 U: Monitors
MFAO Signal Level
10 V = Maximum frequency
(-10 V to +10 V)
10 V = Maximum frequency
(-10 V to +10 V)
10 V = Maximum frequency
(-10 V to +10 V)
10 V = Maximum frequency
(-10 V to +10 V)
10 V = Maximum frequency
(-10 V to +10 V)
10 V = Maximum frequency
(-10 V to +10 V)
No signal output available
No signal output available
10 V = Maximum frequency
(-10 V to +10 V)
MFAO Signal Level
10 V = Motor secondary
rated current (-10 V to +10
V)
10 V = Motor secondary
rated current (-10 V to +10
V)
10 V = Maximum frequency
(-10 V to +10 V)
1
10 V = Motor secondary
rated current (-10 V to +10
V)
200 V class: 10 V = 200
Vrms
400 V class: 10 V = 400
Vrms
(-10 V to +10 V)
121