Comtech EF Data LPOD-R PS .5 Installation And Operation Manual page 127

LPOD-R Outdoor Amplifier / Block Up Converter (BUC)
Optional Serial Interface Operation (PS 1, PS 1.5 ONLY)
Controller-to-Target
Instruction Code and
Parameter Type
Qualifier
(* indicates
End-of-Life)
Command Query
SNMP Enable SNM= SNM?
Serial Number* N/A SNO?
Set Physical SPA= SPA?
(remote) Address
SNMP Read SRC= SRC?
Community
SNMP System SSC= SSC?
Contact
Set Statistics SSI= SSI?
Interval
SNMP System SSL= SSL?
Location
SNMP Unit Name SSN= SSN?
SNMP Trap STA= STA?
Destination IP
Address 1
Arguments for
Command or
Response to
Query
1 byte Command or Query.
Sets or returns SNMP in the form x, where:
0 = Disabled
1 = Enabled
COMMAND EXAMPLE: <0001/SNM=0{CR}
9 bytes Query only.
Returns the unit's nine-digit serial number in the form xxxxxxxxx.
NOTE: This query is functionally identical to RSN.
EXAMPLE: <0001/SNO?{CR}
>0001/SNO=012345678{CR}{LF}
4 bytes Command or Query.
Sets or returns the Physical Address in the form xxxx where:
xxxx = Address value from 0001 (DEFAULT) to 9999.
COMMAND EXAMPLE: <0001/SPA=0412{CR}
16 bytes, Command or Query.
characters, no Sets or returns the SNMP Read Community string.
spaces NOTE: An empty string is not allowed.
COMMAND EXAMPLE: <0001/SRC=public{CR}
255 bytes, Command or Query.
characters, Sets or returns the SNMP System Contact string.
COMMAND EXAMPLE: <0001/SSC=Joe Net Admin{CR}
NOTE: When not configured, the Target returns an empty string: <0001/SSC={CR}{LF}
2 bytes Command or Query.
Sets or returns the time interval, in minutes, at which statistics are logged in the form xx, where:
xx = interval, from 01 to 99 minutes (see NOTE)
NOTE: Default value is 90 minutes.
COMMAN D EXAMPLE: <0001/SSI=90{CR}
255 bytes, Command or Query.
characters, Sets or returns the SNMP System Location string.
COMMAND EXAMPLE: <0001/SSL=Upstairs back right.
NOTE: When not configured, the Target returns an empty string. <0001/SSL={CR}{LF}
16 bytes, Command or Query.
characters, Sets or returns the SNMP Unit Name string.
COMMAND EXAMPLE: <0001/SSN=Remote1{CR}
NOTE: When not configured, the Target returns an empty string. <0001/SSC={CR}{LF}
15 bytes, Command or Query.
Numerical Sets or returns the IP Address of the SNMP Trap Destination IP Address 1 (where
traps will be sent first) in the form xxx.xxx.xxx.xxx, where:
xxx.xxx.xxx.xxx = IP Address
COMMAND EXAMPLE: <0001/STA=010.006.030.001{CR}
NOTE: When not configured, the Target returns >0001/STA=0.0.0.0{CR}{LF}
Description of Arguments
(Note that all arguments are ASCII numeric codes from 48 to 57)
5–23
MN-LPODR
Revision 3
Target-to-Controller
(see Description of Arguments)
Response to Response to
Command Query
SNM= SNM=x
SNM?
SNO= SNO=xxxxxxxxx
SPA= SPA=xxxx
SPA?
SPA*
SRC = SRC=x
SRC!
SSC = SSC=x [1..128]
SSC!
SSI= SSI=xx
SSI?
SSL = SSL=x[1..128]
SSL!
SSN = SSN=x[1..128]
SSN!
STA = STA=xxx.xxx.xx
STA! x.xxx