Sharp AR-M237 Copier Manual page 186

PROGRAMMING
9
Use the numeric keys to enter the fax
number.
DIRECT ADDRESS / RAPID
001
FAX No.
ENTER THE FAX No. VIA THE 10-KEY PAD, THEN PRESS [OK].
0666211221
• To insert a pause between digits of the number, touch
the [PAUSE] key. The pause appears as a hyphen "-".
See page 97 to set the duration of the pause.
• If you make a mistake, press the [CLEAR] key (
to clear one digit at a time, and then enter the correct
digit(s).
• If you are not going to enter a sub-address and
password after the fax number, go to step 12.
• For information on sub-addresses and
Note
passwords, see "TRANSMISSION
BETWEEN MACHINES SUPPORTING
F-CODES" on page 51.
• The maximum number of digits that can
be entered is as follows:
When the destination does not include a
sub-address and passcode, 50 digits
including the fax number and any pauses
(hyphens).
When the destination includes a
sub-address and passcode, 92 digits
including the fax number, any pauses
(hyphens), and slashes "/" (to separate
the sub-address and passcode).
10
If you need to enter a sub-address, touch
the [SUB ADDRESS] key and then enter
the sub-address with the numeric keys.
PRESS [OK].
PAUSE
SUB ADDRESS
11
If you wish to enter a passcode, touch the
[SUB ADDRESS] key once again and enter
the passcode with the numeric keys.
o. VIA THE 10-KEY PAD, THEN PRESS [O
0666211221/3456/
68
NEXT EXIT
CANCEL OK
PAUSE
SUB ADDRESS
)
When you touch the [SUB
ADDRESS] key, a slash is
entered after the fax
number. Enter the
sub-address after the
slash (max. 20 digits).
If you do not wish to enter
a passcode, go to step 12.
When you touch the
[SUB ADDRESS] key, a
slash is entered after the
sub-address. Enter the
passcode after the slash
(max. 20 digits).
12
Touch the [OK] key.
You will return to the rapid key programming
screen.
"REGISTRATION IS COMPLETED." will appear
highlighted to the right of "No.".
The "FAX No." line only shows 32 digits,
Note
regardless of the number of digits stored in
the number.
13
Check the key name.
The characters appearing next to the [KEY
NAME] key will be displayed in the key. Only the
first 18 characters of the name entered in step 1
will be displayed.
If you need to change the name that will be
displayed in the key, touch the [KEY NAME] key
REGISTRATION IS COMPLETED.
NAME SHARP CORPORATION
INDEX USER 3 FAX No
KEY NAME SHARP CORPORATION
14
Check the transmission settings
The initial transmission settings are
"TRANSMISSION SPEED: 33.6 kbps" and
"INTERNATIONAL CORRESPONDENCE
MODE: NONE". To change either of the settings,
touch the [MODE] key.
INITIAL
FAX No. 0666211221/3456/987654
33.6 kbps/NONE
MODE
Transmission speed
Speed selections are 33.6 kbps, 14.4 kbps, 9.6 kbps,
and 4.8 bps. The higher the number, the faster the
transmission speed.
Set the transmission speed only when you
Note
know what speed is most suitable, such as
when you are sending a fax to a foreign
country and telephone line conditions are
bad. If you do not know the line condition, do
not change this setting.
(If you do not wish to
change the name, this
step is not necessary).
See page 80 for the
procedure for entering
characters.
If you do not wish to
change the settings, this
step is not necessary.
After touching the
[MODE] key, you can
change either of the two
settings. When finished,
touch the [OK] key.