Sign In
Upload
Manuals
Brands
LNS Manuals
Lathe
QUICK LOAD SERVO S3
LNS QUICK LOAD SERVO S3 Manuals
Manuals and User Guides for LNS QUICK LOAD SERVO S3. We have
2
LNS QUICK LOAD SERVO S3 manuals available for free PDF download: Troubleshooting And Spare Parts Manual, Startup Manual
LNS QUICK LOAD SERVO S3 Troubleshooting And Spare Parts Manual (132 pages)
Brand:
LNS
| Category:
Lathe
| Size: 5.48 MB
Table of Contents
Table of Contents
2
Chapter 1 Alarms
4
A002 - Emergency Stop Line Open
6
A003 - Lathe Emergency Stop Line Open
7
A004 - Bar Feeder Emergency Stop
8
A006 - Air Pressure Failure
9
A007 - Main Access Cover Open
10
A009 - Bar Feeder Retracted or Not Locked in It's Working Position
11
A011 - Magazine Protection Grid Open
12
A023 - Servo Drive Alarm
13
A024 - Servo Motor Not Ready
14
A025 - Servo Motor Positioning Following Error
15
A042 - Home Position Proximity Switch SQ5 Signal Missing
16
A044 - Bar Loading Error
17
A046 - Clamping Device Has Closed Prior to Feed out Complete
18
A047 - Signal A2 Interrupted During Loading Cycle
19
A048 - Safety Time for Part Feed out Elapsed
20
A049 - Measuring Cell SQ@ Is Activated too Early
21
A050 - Signal A2 Interrupted During Production Cycle and the Clamping
22
A051 - Bar Stock Loading Error
23
A052 - Safety Time for Top-Cut Positioning Elapsed
24
A053 - Lathe DID Not Resume Its Production Cycle
25
A083 - Upper Position Fault
26
A088 - Loading Channel will Not Move to Lower Position
27
A091 - Measuring Cell SQ3 Signal Defective
28
Lower Position Fault
29
Loading Channel Upper Position Default
30
Loading Channel Upper Motion Default
31
Loading Channel Lower Motion Default
32
Loading Channel DID Not Reach Its Lower Position
33
Drive for Diameter Adjustment Error
34
Door Lathe Open
35
Servo Amplifier/Plc Communication Fault
36
Diameter Change Control Device Is out of Sync
37
SPS no Response
38
Mitsubishi Servo Amplifier Alarm List
39
Chapter 2
48
Common Issues
48
Low Voltage / PLC Shutdown
49
Vibration Issues
50
Servo Motor Following Error During Sequence 12
51
Part Feed out Accuracy
52
Chapter 3
54
Procedures
54
End of Bar Adjustment
55
Alignment Procedure
56
Pusher Changeover
60
Carriage Unit Belt Tension Adjustment
63
Servo Motor Belt Tension Adjustment
65
Diameter Adjustment Motor Replacement
67
Home Position Proximity Switch Adjustment - SQ5
71
Magazine and Loading Finger Adjustment
73
Measuring Cell Adjustment - SQ3
74
Pusher Reversing Distance Adjustment
77
Reference Procedure
78
Reset Interface Parameters
80
Calibration of the Loading Table
84
Chapter 4 Software Update/Restore
85
Determining Display Firmware
86
PLC Fault
87
Restore PLC Program from Memory Card to PLC - V1.17A
87
PLC Fault
90
Restore Bar Feeder Parameters from MMI to PLC - V1.17A
90
Software Update
93
Restore Bar Feeder Parameters from MMI to PLC - V1.17A
93
Software Update
96
Restore Display Data from Memory Card to MMI - V1.17A
96
Software Update
100
Restore PLC Program from Memory Card to PLC - V1.17A
100
PLC Fault - V2.08
104
Software Update - V2.08
107
Chapter 5
110
Barfeed Applications
110
Application Setup
111
Chapter 6
114
Preventative Maintenance
114
Daily Maintenance
115
Weekly Maintenance
115
Monthly Maintenance
115
Annual Maintenance
115
Chapter 7
116
Spare Parts
116
Recommended Spare Parts List
117
Parts Order Form
118
Electrical Box Components
119
Loading Table Sub-Assembly (Left/Rear Load)
120
Pusher Locking Sub-Assembly (Left/Rear Load)
123
Loading Table Sub-Assembly (Left/Front Load)
125
Loading Table Sub-Assembly (Left/Front Load)
127
Pusher Locking Sub-Assembly (Left/Front Load)
128
Pusher Locking Sub-Assembly (Left/Front Load)
129
Loading Table Microswitch Sub-Assembly
130
Servo Motor Sub-Assembly
131
Linear Rail Assembly
132
Advertisement
LNS QUICK LOAD SERVO S3 Startup Manual (24 pages)
Brand:
LNS
| Category:
Industrial Equipment
| Size: 0.95 MB
Table of Contents
Table of Contents
2
1 Starting the Bar Feed System
3
Description
3
Settings Related to Installation
3
End of Bar Position Top-Cut Position
3
2 Settings Related to Installation
3
3 Settings Related to Bar Stock and Machined Parts
9
4 Mechanical Settings and Optional Accessories
17
Slope of the Magazine Table
21
5 Putting the Lathe into Operation
23
Spindle Reduction Tubes
23
Advertisement
Related Products
LNS QUICK LOAD SERVO III MI
LNS QUICK LOAD SERVO S3 T BARFEED
LNS QUICK LOAD SERVO 80 S2 BARFEED
LNS QUICK SIX
LNS QUICK SIX S2
LNS Quick Load Servo 65
LNS Quick Load Servo 80
LNS QUICK LOAD SERVO S2
LNS ECO LOAD
LNS ECO LOAD L
LNS Categories
Industrial Equipment
Lathe
Air Cleaner
Dust Collector
Accessories
More LNS Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL