LNS QUICK SIX S2 Manuals

LNS QUICK SIX S2 Manuals

Manuals and User Guides for LNS QUICK SIX S2. We have 1 LNS QUICK SIX S2 manual available for free PDF download: Instruction Manual

LNS QUICK SIX S2 Instruction Manual

LNS QUICK SIX S2 Instruction Manual (84 pages)

Brand: LNS | Category: Industrial Equipment | Size: 3 MB

Table of Contents

Table of Contents
3
Chapter 1: Basic Notions

5
- Structure
  6
- Cross-References
  6
- Symbols and Terminology
  6
- Rights
  7
- Declaration of Conformity
  8
- Safety Instructions
  9
- Safety Devices
  10
- Description
  10
- Layout of the Safety Elements on the Bar Feeder
  10
- Factors Affecting Performance
  11
- Installation
  11
- Distance
  11
- Alignment
  11
- Material
  12
- Bar Stocks
  12
- Tubes
  12
- Material Composition
  12
Chapter 2: Technical Data

13
- Characteristics
  14
- Floor Plans
  14
- Left/Front Loading
  15
- Right/Front Loading
  16
- Layout of the Elements
  17
Chapter 3: Setting into Operation

19
- Transportation
  20
- Unpacking
  20
- Preparation for Mounting
  21
- Mounting
  23
- Chain Loader Supports Setup
  24
- Anchoring to the Ground
  25
- Hydraulic Pump Motor Check
  26
- Filling the Hydraulic Tank
  26
- Interface
  27
- Connections
  29
- Power Supply
  29
- Signals from the Lathe to the Bar Feeder
  30
- Emergency Stop Signal
  30
- Lathe Clamp Signal
  30
- Load Command
  30
- R1 Alarm Relay
  31
- R2 Start and Stop of the Lathe
  31
- R3 End of Bar Signal Relay
  31
- R4 Spindle Interlock Relay
  31
- Options
  32
- R5 Auxiliary End of Bar Relay
  32
- R10 Bar Stock Magazine Empty Relay
  32
- Recapitulation of Safety Instructions Related to the Interface
  32
Chapter 4: Operation

33
- Powering On/Off
  34
- Remote Control
  35
- Display
  36
- Function Keys F1-F4
  37
- Left/Right/Up/Down Keys
  37
- Emergency Stop Switch
  37
- Stop Key
  37
- Set up
  38
- Bar Feeder Mechanical Setup
  38
- Retraction Device
  38
- Guiding Element Choice
  39
- Guiding Element Changeover
  39
- Pusher Changeover
  39
- Pusher Holding System Setup
  40
- Lathe Mechanical Setup
  41
- Clamping Method
  41
- 3-Jaws Chuck
  41
- Bi-Conical Collet
  41
- Lathe - Bar Feeder Adaptation
  42
- Spindle Reduction Tubes
  42
- Soft Grips
  42
- Chain Loader
  43
- Loading a Bar Stock on the Chain Loader
  43
- Use and Setup of the Dropping Fingers
  43
- Unloading a Bar Stock
  43
- Positioning Parameters Setup
  44
- End of Bar Position
  44
- End of Bar Setting
  44
- Screen "End of Bar Position"
  45
- Top-Cut Position
  46
- Top Cut Position Setting
  46
- Screen "Top Cut Position"
  47
- Access to the Functions
  48
- Part Setup
  48
- Application Setup
  48
- Position/Torque
  48
- Material Shape
  49
- Bar Stock Diameter
  49
- Total Part Feed out Length
  49
- Number of Clamping Device Openings for Overall Length
  50
- Pusher Reverse Distance after Feeding
  50
- Optional Auxiliary End of Bar
  50
- Part Feed out Length after Aux. EOB
  51
- Number of Clamping Device Openings after Aux. EOB
  51
- Auxiliary End of Bar Position
  51
- Part Feed out with Turret
  52
- Part Feed out Without Turret
  52
- Part Feed out with M-Function
  52
- Dry Run
  52
- Top-Cup Position
  53
- Miscellaneous Functions
  54
- Language
  54
- Unit of Measure
  54
- Request for Reference Point
  54
- Service
  55
- Password
  55
- Bar Feeder
  55
- Automatic Cycle
  56
- New Loading Bar Stock
  56
- Part Feed out
  56
- Remnant Extraction
  56
- Maintenance
  57
- Periodic Maintenance
  58
- Caution on Cleaning
  58
- Periodic Control Plan
  58
- Mechanical Operations
  59
- Pusher Holding Rolls Replacement
  59
- Electrical Equipment
  59
- Layout of Electrical Elements
  60
- Electrical Cabinet
  62
- Replacement of the Fuse of the Transformer T1
  63
- To Replace the Fuse
  63
- Servo Amplifier
  64
- Programmable Controller
  66
- Battery Module
  66
- M1 Slot
  66
- M2 Slot
  66
- PLC Input/Outputs
  67
- Circuit Breakers
  68
- Main Disconnect Switch QS1
  68
- Main Circuit Breaker QM1
  68
- Circuit Breaker QF1
  68
- Hydraulic Equipment
  69
- Setting
  69
- Filling and Draining
  69
- Viscosity Equivalency Table
  69
- Pneumatic Equipment
  70
- Pneumatic Setup
  70
- Connection
  70
- Settings
  70
- Pneumatic Valve Battery
  71
- Description of the Elements
  72
- Solenoid Valves
  72
- Air Pressure Switch
  72
- Pneumatic Drawing
  73
- Spare Parts
  74
- Mechanics
  74
- Hydraulic
  74
- Electric
  74
- Programming Example
  77
- Main Program
  77
- Part Program
  77
- Sub-Program
  77
- Parts Library Specifications
  79
- Functions
  79
- Add Parts
  80
- Loading/Deleting Parts
  81
- Deleing Parts
  81
- Ftp
  82
- Accessing the Files
  82
- Backup
  82
- Closing the FTP Session
  83

Advertisement

Advertisement

Related Products

LNS Categories

Industrial Equipment Dust Collector Lathe Air Cleaner Accessories

More LNS Manuals