Kyocera 5035 Operation Manual page 111

6 Specifying the direction that the originals were set
This procedure specifies the direction of the set originals.
1
With the content of the "Basic" tab displayed, touch the
"Orig.set direction" key. The "Orig.set direction" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1 sided
11x8 1 / "
2
Select
Original
paper type
Offset AMS
Reduce
Finished
/Enlarge
Basic Quality
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build -Step 1
1-sided
Select
Original
paper
type
Group AMS
Reduce/
Finished
Enlarge
Basic Quality
2 Touch the "Rear" ["Back Edge"] key or the "Left top corner"
key, as appropriate, according to the direction of the
originals.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Org. set direction
" C h e ck d i r e c t i o n o r i g i n a l " c a n b e s h ow n
a t r i g h t s i d e o f d i s p l ay.
Fo l l ow t h e s t e p s. I f s e t t i n g m o d e i s
w r o n g , i n c o r r e c t c o py w i l l r e s u l t .
Metric specifications
Ready to Job build.
Set original. Press Start key.
Orig. set direction
" C h e ck d i r e c t i o n o r i g i n a l " c a n b e s h ow n
a t r i g h t s i d e o f d i s p l ay.
Fo l l ow t h e s t e p s. I f s e t t i n g m o d e i s
w r o n g , i n c o r r e c t c o py w i l l r e s u l t .
IMPORTANT!
If the designation for the direction that the originals are set is not
correct, copying may be accomplished incorrectly.
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
1 sided copy
Insert
page
1 sided/
2 sided
1 sided copy-Left
Back Edge
Finished page #:0
Orig. set
direction
Edit
1-sided Copy
Insert
blank page
1-sided/
2-sided
1-sided Copy-Left
Back Edge
Finished page #: 0
Orig. set
direction
Edit
Back
Check direction
Check direction of
original top side.
Left top
Rear
corner
Back
Check direction
Check direction of
original.
Left top
Back Edge
corner
Section 5 OTHER CONVENIENT FUNCTIONS
7 Setting the scanning density
This procedure sets the copy exposure for the finished copies.
1
Touch the "Quality" key. Then, in the resulting screen, touch
the "Exposure mode" key. The "Exposure mode" screen will
be displayed.
Inch specifications
Set
Ready to Job build.
Place originals then press Start key.
End Job Build - Step1
Density 4
Exposure
mode
Basic
Metric specifications
Set
Ready to Job build.
Set original. Press Start key.
End Job Build - Step1
Manual 4
Exposure
mode
Basic
2 If you want to have the copy exposure selected
automatically, touch the "Auto" key.
If you want to manually set the exposure, touch the "Manual"
key and then touch the "Lighter" key or the "Darker" key to
move the cursor on the exposure scale and adjust the
Set exposure as desired.
Inch specifications
Close
Ready to Job build.
Place originals then press Start key.
Exposure mode
Auto
Manual
Set
Metric specifications
Close
Ready to Job build.
Set original. Press Start key.
Exposure mode
Auto
Manual
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
Text+Photo Off
Orig. image
Eco Print
quality
1 sided copy-Left
Finished page # : 0
Quality Edit
Text + Photo Off
Image
Eco Print
quality
1-sided Copy-Left
Finished page #: 0
Quality Edit
Lighter Darker
Lighter Darker
Set
End
Insert
page
Set
End
Insert
blank page
Set
Back Close
Set
Back Close
5-65