Details Of Trouble Code; A0-01 Pcu Rom Abnormality; A0-02 Scu Rom Abnormality; A0-10 Controller Rom Error - Sharp MX-2300 G Service Manual

3. Details of trouble code

A0-01 PCU ROM abnormality
Trouble content PCU ROM content trouble
Section PCU
Case 1 Cause Firmware upgrade is not made properly due to power
OFF, etc.
Check Use SIM49-1 to upgrade the firmware.
and
remedy
A0-02 SCU ROM abnormality
Trouble content SCU ROM content trouble
Section Scanner
Case 1 Cause Some part of SFU is not upgraded during upgrading of
the firmware.
Check Use SIM49-1 to execute the firmware.
and
remedy
A0-10 Controller ROM error
Trouble content SFU combination error in the controller
Section MFP
Case 1 Cause SFU upgrade was not properly made when upgrading
the firmware.
Check Controller firmware upgrade
and
remedy
A0-11 IF version discrepancy (CTL-PCU)
Trouble content Combination error between CTL and PCU
Section MFP
Case 1 Cause Combination error between CTL and PCU
Check Check the firmware combination between CTL and
and PCU.
remedy
A0-12 IF version discrepancy (CTL-SCU)
Trouble content Combination error between CTL and SCU
Section MFP
Case 1 Cause Combination error between CTL and SCU
Check Check the firmware combination between CTL and
and SCU.
remedy
A0-20 Machine level error (CTL detection)
Trouble content Combination error between the machine production/
remodeling and the firmware
Section MFP
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check Check the combination between the machine
and production/remodeling and the firmware.
remedy
A0-21 Machine level error (PCU detection)
Trouble content Combination error between the machine production/
remodeling and the firmware
Section PCU
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check Check the combination between the machine
and production/remodeling and the firmware.
remedy
MX-2300/2700 N/G SELF DIAG AND TROUBLE CODE 8 – 8
A0-22 Machine level error (SCU detection)
Trouble content Combination error between the machine production/
remodeling and the firmware
Section Scanner
Case 1 Cause Combination error between the machine production/
remodeling and the firmware
Check Check the combination between the machine
and production/remodeling and the firmware.
remedy
CE-00 Communication error other than CE-
01 – 08
Trouble content Another communication error occurs.
Section MFP
Case 1 Cause Network cable connection trouble
Check Check to insure that the network cable is securely
and connected.
remedy
CE-01 Network controller trouble
Trouble content Network controller and its peripheral circuit trouble
Section MFP
Case 1 Cause Network controller and its peripheral circuit trouble
Check 1) Check the network controller and its peripheral
and circuit.
remedy 2) Output the NIC Config Page and check the NIC
version.
3) Replace the MFPcnt PWB.
CE-02 Not-specified mail/FTP server error
Trouble content The specified mail server, FTP server, and SMB
server are not found
Section MFP
Case 1 Cause Network cable connection trouble
Check Check to insure that the network cable is securely
and connected.
remedy
Case 2 Cause Network setup trouble
Check 1) Check that the connected network supports TCP/
and IP protocol.
remedy 2) Check from Web page that the Primary/
Secondary E-mail Server Address or the FTP
server/Desktop PC/SMB server address as the
destination is properly set.
3) When the above address is described with the
Hostname, check that the DNS server is properly
set or not.
Case 3 Cause SMTP server/FTP server/NST/SMB server trouble
Check Check the SMTP server/FTP server/NST/SMB server
and for any trouble.
remedy
CE-03 Communication error in image send
Trouble content The specified server does not respond during image
send.
Section MFP
Case 1 Cause Network cable connection trouble
Check Check to insure that the network cable is securely
and connected.
remedy
Case 2 Cause SMTP server/FTP server/NST/SMB server trouble
Check Check the SMTP server/FTP server/NST/SMB server
and for any trouble.
remedy