Sharp MX-2300 G Service Manual page 175

46-19
Purpose : Setting
Function (Purpose) : Used to set the BLACK auto exposure
mode.
Section : Scanner
Item : Operation
Operation/Procedure
1) When the machine enters the simulation, the current set status
is highlighted.
2) Press a set value button to be changed, and the button is high-
lighted and the set value is saved to EEPROM and RAM. (In
this example, [MODE2] button is pressed.)
* Only one item can be selected.
* When [CLOSE] button is pressed, the display is shifted to the
copy basic screen of simulation.
* Copying can be performed also by pressing [COLOR]/[BLACK]
key.
<Set range and default value of each set value>
Item Content
AE_MODE Auto exposure mode
AE_STOP_COPY Auto BLACK exposure STOP
(for copy)
AE_STOP_FAX Auto BLACK exposure STOP
(for FAX)
AE_STOP_SCAN Auto BLACK exposure STOP
(for scanner)
SIMULATION NO.46-19
TEST
EXPOSURE MODE SETUP (B/W-AE)
AE MODE : MODE1
AE STOP COPY :
OFF
AE STOP FAX :
OFF
AE STOP SCAN :
OFF
46-21
Purpose : Adjustment
Function (Purpose) : Used to perform the copy color balance
manual correction.
[Color, All modes]: PG print
Section : Engine
Item : Adjustment
Operation/Procedure
1) Select a color with [K][C][M][Y] buttons. The adjustment value
of the selected color is displayed. (In this example, [C] is
selected.)
* Only one color button can be selected. The selected button
is highlighted. (On the default display, [K] is selected.)
* Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
Default
Set value
value
MODE1, MODE1
MODE2
ON/OFF ON
ON/OFF ON
ON/OFF ON
0
CLOSE
MODE2
ON
ON
ON
1/1
MX-2300/2700 N/G SIMULATION 7 – 69
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
* The set values can be collectively changed by pressing [ ]
[ ] buttons.
When the set value is not the upper limit value (lower limit
value), the data of each item is increased (decreased) by 1.
3) When [EXECUTE] button is pressed, it is highlighted, and self
print is started.
* When [OK], [EXECUTE], [↑], [↓], [ ], [ ] button, [COLOR],
or [BLACK] key is pressed, the data are saved to EEPROM
and RAM.
* After completion of self print, [EXECUTE] button returns to
the normal display.
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key
is pressed during self-printing, the operation is stopped.
<Set range and default value of each setup>
Item Display Item
A POINT1 Point 1
B POINT2 Point 2
C POINT3 Point 3
D POINT4 Point 4
E POINT5 Point 5
F POINT6 Point 6
G POINT7 Point 7
H POINT8 Point 8
I POINT9 Point 9
J POINT10 Point 10
K POINT11 Point 11
L POINT12 Point 12
M POINT13 Point 13
N POINT14 Point 14
O POINT15 Point 15
SIMULATION NO.46 21
TEST
ENGINE COLOR BALANCE MANUAL ADJUSTMENT [ALL(COLOR)]
A 500
POINT1
A:
500
B 500 POINT2
C 500 POINT3
245~755
D :500 POINT4
K
C M
Y
46-23
Purpose : Setting
Function (Purpose) : Used to set ENABLE/DISABLE of the half
tone highest density correction.
Section :
Item : Specifications
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
2) When [OK] button, [COLOR] or [BLACK] key is pressed, the
current entered value is saved to EEPROM and RAM.
<Set range and default value of each setup>
Item Display
A (0: ENABLE 0 Engine highest density
1: DISABLE) correction mode ENABLE
1 Engine highest density
correction mode DISABLE
Set range Default value
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
245 to 755 500
CLOSE
EXECUTE
Set Default
Content
range value
0 to 1
0
OK
0