Sharp MX-2300 G Service Manual page 193

SIMULATION NO.46-45
TEST
EXPOSURE ADJUSTMENT(FAX 600DPI)
A 50
AUTO
A:
50
B 50 EXPOSURE1
1 99
C 50 EXPOSURE2
D 50 EXPOSURE3
46-47
Purpose : Setting
Function (Purpose) : Used to set the JPEG compression rate in
Copy/Scanner (PUSH SCAN).
Section : —
Item : Setting
<Set range and default value of each setup>
Category Item
COPY (COLOR) A
COPY (GRAY) B
PUSH SCAN (COLOR) C
PUSH SCAN (GRAY) D
SIMULATION NO.46 47
TEST
COPY SCAN COMPRESS RATE ADJUSTMENT
A 0
COPY(C)
A:
0
B 0 COPY(G)
C 0 SCAN(C)
0 2
C 0 SCAN(G)
48
48-1
Purpose : Adjustment
Function (Purpose) : Used to execute the magnification adjust-
ment in the scan system (for RSPF).
Section : RSPF/Scanner
Item : Image quality (Size/magnification ratio)
Operation/Procedure
1) Select the set item with [↑] and [↓] buttons.
CLOSE
EXECUTE
Display
COPY (C) LOW Low compression (Color)
MIDDLE Middle compression (Color)
HIGH High compression (Color)
COPY (G) LOW Low compression (Gray)
MIDDLE Middle compression (Gray)
HIGH High compression (Gray)
SCAN (C) MIDDLE1 Middle compression mode 1, for compression, Q table (for
brightness, color difference)
Middle compression mode 1, for decompression, Q table (for
brightness, color difference)
MIDDLE2 Middle compression mode 2, for compression, Q table (for
brightness, color difference)
Middle compression mode 2, for decompression, Q table (for
brightness, color difference)
MIDDLE3 Middle compression mode 3, for compression, Q table
Middle compression mode 3, for decompression, Q table
SCAN (G) MIDDLE1 Middle compression mode 1, for compression, Q table
Middle compression mode 1, for decompression, Q table
MIDDLE2 Middle compression mode 2, for compression, Q table
Middle compression mode 2, for decompression, Q table
MIDDLE3 Middle compression mode 3, for compression, Q table
Middle compression mode 3, for decompression, Q table
CLOSE
LOW
LOW
MIDDLE
MIDDLE
MX-2300/2700 N/G SIMULATION 7 – 87
Operation/Procedure
0
1) Select the set item with [↑] and [↓] buttons.
The highlighted set value is switched and the value is dis-
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
OK
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the currently entered data are saved to EEPROM and
RAM.
Content
The highlighted set value is switched and the value is dis-
0
played in the setting area.
* If there is any item over [↑], an active display is made and
item is shifted.
If there is no item over [↑], the display grays out and the
operation is invalid.
If there is any item under [↓], an active display is made and
item is shifted.
If there is no item over [↓], the display grays out and the
OK
operation is invalid.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered values.
3) When [OK], [↑], [↓] button, [COLOR], or [BLACK] key is
pressed, the current entered value is saved to EEPROM and
RAM.
* Copying can be performed also by pressing [COLOR]/
[BLACK] key.
* When [CLOSE] button is pressed, the display is shifted to
the copy basic screen of simulation.
Set range Default value
0 0 (LOW)
1
2
0 0 (LOW)
1
2
0 0 (MIDDLE1)
1
2
0 0 (MIDDLE1)
1
2