9 ] Trouble Code List - Sharp AR-280 Service Manual

[9] TROUBLE CODE LIST
1. Trouble code
Trouble
Content of trouble
code
C1 00 MC trouble
C2 00 TC trouble
E7 00 ICU communication trouble
01 Image data memory trouble
02 Laser trouble
03 HDD trouble
10 Shading trouble (Black correction)
11 Shading trouble (White correction)
13 CCD light quantity check error
90 ICU communication trouble
F1 00 Finisher communication trouble
01 Finisher 1 jogger shift trouble / Finisher 2
alignment section abnormality
02 Finisher transport motor abnormality
03 Sorter guide bar oscillation motor trouble
04 Finisher 1 elevator lower limit detection /
Finisher 2 stack tray lower limit detection
05 Finisher 1 elevator home / Finisher 2
stack tray sensor abnormality
06 Finisher shift motor abnormality
08 Finisher staple shift motor trouble
10 Finisher staple unit operation trouble
11 Finisher 1 pusher motor trouble / Finisher
2 boomerang rotation abnormality
14 Finisher 2 stack tray abnormality
15 Finisher 1 elevator motor trouble /
Finisher 2 stack tray motor lock
16 Staple sorter holding moter trouble
17 ST paper exit roller pressure release
trouble
18 Tray 3 paper exit paddler operation trouble
50 Non-suport trouble in automatic detection
of option connection (Sorter, finisher)
80 Finisher power not supplied
F2 00 Toner control sensor open
02 Toner motor connector unconnected
31 Process control trouble (OPC drum
surface reflection rate abnormality)
32 Process control trouble (Drum marking
scanning trouble)
37 Drum marking sensor gain adjustment
error
39 Process thermistor breakdown
F3 12 Copier top stage CS lift up trouble
22 Copier bottom stage CS lift up trouble
F9 00 Printer communication trouble
01 PRT DRAM trouble
02 PRT Centroport check error
03 Network card trouble
04 Printer program error
10 PRT SCSI LSI abnormality
90 Printer communication trouble
H2 00 Thermistor open (HL1)
01 Thermistor open (HL2)
H3 00 Heat roller high temperature detection
(HL1)
01 Heat roller high temperature detection
(HL2)
H4 00 Heat roller low temperature detection
(HL1)
01 Heat roller low temperature detection
(HL2)
H5 01 3 continuous POD1 not-reaching JAM
detection
02 Fusing thermistor abnormality
L1 00 Scanner feed trouble
Trouble Trouble
Remark
detection
PCU L3
PCU L4
ICU L6
ICU L8
ICU
ICU U2
ICU
ICU
ICU
U4
PCU
PCU
FIN
U5
FIN
SOT
FIN
FIN
FIN
FIN
FIN
FIN
U6
FIN
FIN
SOT
FIN
FIN
PCU
FIN
PCU
PCU
PCU
U7
PCU
U9
PCU
CE
PCU
PCU
PCU
ICU
PRT
PRT
ICU
PRT
CH Light
PCU
PCU
EE
PCU
PCU
FA
PCU
FC
PCU
PC
PF
PCU
– –
PCU
PCU
9 – 1
Content of trouble
code
00 Scanner return trouble
01 Main motor lock detection
10 Polygon motor lock detection
01 No full-wave signal
02 Full-wave signal width abnormality
00 EEPROM read/write error
11 Counter check sum error (EEPROM)
12 Adjustment value check sum error
(EEPROM)
02 ADU alignment plate operation
abnormality
03 ADU rear edge plate operation
abnormality
00 RADF/SPF/RSPF communication trouble
01 RADF resist sensor trouble
02 RADF eject/inversion sensor trouble
03 RADF timing sensor trouble
06 RSPF post-separation sensor trouble
07 RSPF read sensor trouble
08 RSPF SB sensor trouble
11 RADF paper feed motor operation
abnormality
16 RSPF fan motor operation abnormality
00 Desk communication trouble
01 Desk 1 CS lift up trouble
02 Desk 2 CS lift up trouble
03 Desk 3 CS lift up trouble
08 Desk 24V power abnormality
09 LCC lift motor trouble
10 Desk transport motor trouble
20 LCC communication trouble
21 LCC transport motor trouble
22 LCC 24V power abnormality
50 Non-suport trouble in automatic detection
of option connection (Desk unit)
51 Non-suport trouble in automatic detection
of option connection (LCC unit)
00 RIC communication trouble
00 Operation control communication trouble
90 Operation control communication trouble
00 The other communication error has
occurred.
01 The print server card (AR-NC3D) is not
installed or defective.
02 The specified mail server or the FTP
server is not found.
03 The specified server does not correspond
during image transmission.
04 The entered account name of the FTP
server or the password is invalid.
05 The entered directory of the FTP server is
invalid.
Door open
up
EL Auto developing adjustment trouble
(Overtoner)
EU Auto developing adjustment trouble
(Undertoner)
00 SCSI trouble
00 ASK/IrDA modulation LSI reset error
01 ASK/IrDA switch error
Personal counter not installed
RIC copy inhibit command reception
Auditor not ready
Trouble
Remark
detection
PCU
PCU
ICU
PCU
PCU
ICU
ICU
ICU
PCU
PCU
PCU
RADF
RADF
RADF
RSPF
RSPF
RSPF
RADF
RSPF
PCU
Desk
Desk
Desk
Desk
LCC
Desk
PCU
LCC
LCC
PCU
PCU
PCU
ICU
OPE
Network
Network
Network
Network
Network
Network
PCU
In SIM only PCU
In SIM only PCU
ICU
ICU
ICU
ICU
7/13/2000