Sharp MX-2300 G Service Manual page 118

SIMULATION NO.03 03
TEST
FIN LOAD CHECK
FINRPS FJPM
FPM FAM
FSM FFSM
3-10
Purpose : Adjustment
Function (Purpose) : Used to adjust the finisher.
Section : Finisher
Item : Operation
Operation/Procedure
1) Select the item according to the adjustment content with [↑] [↓]
buttons.
2) Enter the adjustment value with 10-key.
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
Item Display
A SADDLE POSITOIN Saddle binding
position adjustment
B FOLDING POSITION Saddle folding
position adjustment
C FRONT ADJUST Alignment position
adjustment (front)
D REAR ADJUST Alignment position
adjustment (rear)
E STAPLE REAR Staple binding
position adjustment
(one position at the
rear)
F STAPLE FRONT Staple binding
position adjustment
(one position in front)
G STAPLE BOTH Staple binding
position adjustment
(two positions at the
center)
H STAPLE PITCH Staple binding
position adjustment
(two positions in
pitch)
I PUNCH CENTER Punch center
adjustment
J PUNCH HOLE Punch hole position
adjustment
<Inner finisher>
Item Display
A FRONT ADJUST Alignment position
adjustment (front)
B REAR ADJUST Alignment position
adjustment (rear)
C STAPLE REAR Staple binding position
adjustment (one
position at the rear)
D STAPLE FRONT Staple binding position
adjustment (one
position in front)
E STAPLE BOTH Staple binding position
adjustment (two
positions at the
center)
0
CLOSE
FJFM FFM
FFJM FRJM
FLM
FFC
1/1
EXECUTE 1/1
Set Default
Item
range value
0 to 400 200
0 to 400 200
0 to 20 10
0 to 20 10
0 to 200 100
0 to 200 100
0 to 200 100
0 to 100 50
47 to 53 50
0 to 100 50
Set Default
Item
range value
2 to 18 10
2 to 18 10
68 to 132 100
68 to 132 100
68 to 132 100
MX-2300/2700 N/G SIMULATION 7 – 12
Item Display
F STAPLE PITCH Staple binding position
adjustment (two
positions in pitch)
G PUNCH CENTER Punch center
adjustment
H PUNCH HOLE Punch hole position
adjustment
[Screen (Saddle finisher installed)]
SIMULATION NO.03-10
TEST
FINISHER ADJUSTMENT
A 200
SADDLE POSITION
A:
200
B 200 FOLDING POSITION
C 10 FRONT ADJUSUT
0 400
D 10 REAR ADJUSUT
4
4-2
Purpose : Operation test/check
Function (Purpose) : Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray and the related circuit.
Section : Desk/Large capacity tray (LCC)
Item : Operation
Operation/Procedure
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
DCSI1 Desk 1 installation detection
DPFD1 Desk 1 transport detection
DLUD1 Desk 1 upper limit detection
DPED1 Desk 1 paper empty detection
DCSPD1 Desk 1 remaining paper quantity detection
DCSS11 Desk 1 rear edge detection 1
DCSS12 Desk 1 rear edge detection 2
DCSS13 Desk 1 rear edge detection 3
DCSS14 Desk 1 rear edge detection 4
DCSI2 Desk 2 instillation detection
DPFD2 Desk 2 transport detection
DLUD2 Desk 2 upper limit detection
DPED2 Desk 2 paper empty detection
DCSPD2 Desk 2 remaining paper quantity detection
DCSS21 Desk 2 rear edge detection 1
DCSS22 Desk 2 rear edge detection 2
DCSS23 Desk 2 rear edge detection 3
DCSS24 Desk 2 rear edge detection 4
DSW_DSK Desk transport cover open/close detection
<A4 LCC sensor>
LPFD LCC transport sensor
LUD LCC tray upper limit sensor
LDD LCC tray lower limit sensor
LPED LCC tray paper empty sensor
LCD LCC tray insertion detection
LDSW LCC upper open/close detection SW
LRE LCC lift motor encoder sensor
L24VM LCC24V power monitor
LLSW LCC upper limit SW
LTOD LCC main unit connection detection
Set Default
Item
range value
68 to 132 100
37 to 63 50
42 to 58 50
0
CLOSE
OK