Korg microX Operation Manual Page 107

Synthesizer/controller.
Hide thumbs
Tone No.
Creating an example pattern
1. Set "Step (Step No.)" to 01, and press the center
of the ClickPoint.
2. Select Tone 0, and press the center of the
ClickPoint.
3. Use the ClickPoint [®] to change "Step" to 02,
and enter Tone 1.
4. In the same way, change "Step" to 03 and enter
Tone 2.
5. Set "Step" to 04 and enter Tone 1.
6. Set "Step" to 05 and enter Tone 3.
7. Set "Step" to 06 and enter Tone 1.
8. Set "Step" to 07 and enter Tone 2.
9. Set "Step" to 08 and enter Tone 1.
10.Press the [MENU/OK] button.
11.When you play the keyboard as shown in the
illustration, the arpeggiator will begin playing.
Tone 0 corresponds to the pitch of the lowest
key of chord you play on the keyboard. (If
"Sort" is unchecked, it will correspond to the
pitch of the first note you play.)
12.For steps 01–08, make settings for "Ptch (Pitch
Offset)," "Gt (Gate)," "Vel (Velocity)," and
"Flam."
"Ptch (Pitch Offset)": This offsets the pitch of
the arpeggio note in semitones up or down.
You can input the same tone for each step, and
change the "Ptch (Pitch Offset)" value for each
4
3
2
1
0
01
05
Step No.
Lgth(Length)
Creating a user arpeggio pattern
to create a melody using a single tone.
(☞"Melody pattern")
"Gt (Gate)": Specify the length of the arpeggio
note for each step. With a setting of LGT, the
note will continue sounding either until the
next note of the same tone or until the end of
the pattern. With a setting of Off, the note will
not sound.
"Vel (Velocity)": Specify the strength of the note.
With a setting of Key, the note will sound at the
strength with which it was actually played.
Note: The "Gt (Gate)" and "Vel (Velocity)"
settings you make here will be valid if the "Gt
(Gate)" and "Vel (Velocity)" parameters (PROG
7: Ed–Arp/Ctrls, Setup page) of the program
selected in Program mode are set to Step. If
these parameters have a setting other than
Step, the "Gt (Gate)" and "Vel (Velocity)" that
were specified for each individual step will be
ignored, and all notes of the arpeggio will
sound according to the settings in PROG 7: Ed–
Arp/Ctrls. Be sure to verify the settings of the
program.
Note: Before you set "Gt (Gate)," move the
REALTIME CONTROLS C-mode [ARP-GATE]
knob to the center position (12 o'clock).
Note: Before you set "Vel (Velocity)," move the
REALTIME CONTROLS C-mode [ARP-
VELOCITY] knob to the center position (12
o'clock).
13.To change the user arpeggio pattern name, use
the Utility "Rename Arpeggio Pattern"
(☞p.114).
14.If you wish to save the edited user arpeggio
pattern to internal memory, be sure to Write the
user arpeggio pattern (☞p.104).
If you turn off the power without writing, the
edited contents will be lost.
15.If you wish to save the state of the program at
the same time, return to Program mode and
write the program (☞p.45).
101

Advertising

   Also See for Korg microX

   Related Manuals for Korg microX

Comments to this Manuals

Symbols: 0
Latest comments: