Korg microX Operation Manual page 88

Effects settings
BUS Select (All OSCs) = 1/2
IFX / Indiv.Out
Pan BUS Select
OSC 1
BUS Select
= 1/2
OSC 2
Select from:
L/R
IFX
1
2
1/2
Off
BUS Select (All OSCs) = Off
IFX / Indiv.Out
Pan BUS Select
OSC 1
BUS Select
= Off
OSC 2
Select from:
L/R
IFX
1
2
1/2
Off
3. "MFX Send" specifies the send level from each
oscillator to the master effects.
This is valid only if "BUS Select (All OSCs)" is
set to L/R or Off.
If IFX is selected for "BUS Select (All OSCs),"
the send level to the master effects is adjusted
by the "Send 1 (MFX1)" and "Send 2 (MFX2)"
parameters (PROG 8: Ed–InsertFX, Setup page)
after the signal has passed through the insert
effect.
Selecting an insert effect, and rout-
ing after the insert effect
1. Access the PROG 8: Ed–InsertFX, Setup page.
The Setup page displays the state of the routing
and the insert effect settings. In this page you
can also make "BUS Select" settings. Use the
ClickPoint to choose (All OSCs), and use the
[VALUE] dial etc. to make a selection.
Insert Effect
IFX On/Off Pan (CC#8)
BUS Select
82
PROG 8: Insert FX
Post IFX
Insert Effect Pan(CC#8)
stereo
IFX
IFX BUS
mono x 2
PROG 8: Insert FX
Post IFX
Insert Effect Pan(CC#8)
stereo
IFX
IFX BUS
mono x 2
BUS Select Send2(MFX2)
Send1(MFX1)
IFX On Insert Effect
Send2
Send1
Post IFX
BUS Select
Send1 / 2
BUS Select
= L/R
Select from:
L/R
1
2
Master Effects
Chain
1/2
Off
MFX1
mono
MFX2
mono
mono x2
Send1 Send2
Post IFX
BUS Select Send1 / 2
BUS Select
= L/R
Select from:
L/R
1
2
Chain Master Effects
1/2
Off
MFX1
mono
MFX2
mono
mono x2
2. In "Insert Effect," select the desired insert
effect.
You can press the [CATEGORY] button and
choose an effect from six categories.
3. In "IFX On/Off," turn the insert effect on/off.
If this is set to Off, the result will be the same as
if 00: No Effect is selected. The input sound
will be output without change.
Note: You can use the Utility "Copy Insert
Effect" to copy effect settings from another
program, etc.
4. Set the "Pan (CC#8)," "BUS Select," "S1 (Send1
(MFX1))," and "S2 (Send2 (MFX2))" parameters
that follow the insert effect.
"Pan (CC#8)": Set the pan. This is valid only if
"BUS Select" is set to L/R.
"BUS Select": Specify the output destination.
Normally you will set this to L/R. If you want
to output the sound from (INDIVIDUAL
OUTPUT) 1 and/or 2, set this to 1, 2, or 1/2.
"Send1 (MFX1)," "Send2 (MFX2)": Set the
send level to the master effects. For this
example, set these to 127.
PROG 9: Master FX
L/R BUS
AUDIO OUTPUT
Master EQ
stereo
(MAIN) L/MONO, R
Return1 / 2
stereo
stereo
AUDIO OUTPUT
(INDIVIDUAL)1/2
PROG 9: Master FX
L/R BUS
AUDIO OUTPUT
Master EQ
stereo
(MAIN) L/MONO, R
Return1 / 2
stereo
stereo
AUDIO OUTPUT
(INDIVIDUAL)1/2