Sharp AR-M455N Service Manual page 210

SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE?
1. YES
2. NO
Press [START] key.
SIMULATION 66-35
MODEM PROGRAM RELOAD. EXECITOMG···
LOADER··· xxxxx
MODEM···· xxxxx
After completion of reloading
SIMULATION 66-35
MODEM PROGRAM RELOAD.
LOADER···OK
MODEM····COMPLETE
66-36
Purpose Operation test/Check
Function Used to check interface between MFPC controller
(Purpose) and MDMC. (Check of the data line or the
command line) (Only when FAX is installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-
key.
MFPC ← MDMC
1 Date line once only
MFPC → MDMC
2 Date line once only
MFPC ← MDMC
3 Data line repeat
MFPC → MDMC
4 Data line repeat
MFPC ← MDMC
5 Command line once only
MFPC → MDMC
6 Command line once only
MFPC ← MDMC
7 Command line repeat
MFPC → MDMC
8 Command line repeat
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of
an error, "NG" is displayed.
When check is "repeat," the operation is continued until the result
is NG or [CUSTOM SETTINGS] key is pressed.
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MDPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)
Press [START] key.
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...
When check is "once" or When check is "repeat" and
"repeat" and the result is "NG": [CUSTOM SETTINGS] key ON:
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)
66-39
Purpose
Function
(Purpose)
1
Section
Item
Operation/Procedure
1) Enter the number corresponding to the destination.
2) Press [START] key.
SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1-6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A./CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA
66-42
Purpose
Function
(Purpose)
Section
Item
Operation/Procedure
1) The confirmation window is displayed. Select whether rewrit-
ing of the program into PIC installed in the FAX VOX is per-
formed or not.
NOTE: Release the write protect notch.
FAX program writing enabled (Jumpers and DIP SW
depending on the model.)
1 YES
2 NO
2) Press [START] key.
When reload is completed normally, "OK" is displayed. In case of
an error, "NG" is displayed.
NG cause:
• Write protect is set.
• PIC is not installed.
• Access error to PIC
1
SIMULATION 66-42
PIC PROGRAM RELOAD.
ARE YOU SURE ?
1.YES
2.NO
SIMULATION 66-42
PIC PROGRAM RELOAD EXECUTING ... .
SIMULATION 66-42
PIC PROGRAM RELOAD
OK
AR-M355N/M455N SIMULATION 9 - 84
Setting
Used to set the destination specifications. (Only
when FAX is installed)
FAX
Specifications
Press [START] key.
Setting
PIC program rewriting (Only when FAX is
installed)
FAX
Operation
Execution
Cancel
Press [START] key.
Press [START] key. Press [CUSTOM SETTINGS] key.
Operation
1
1