Sharp AR-M455N Service Manual page 188

Item
Scanner mode
10 OC (LEAD_EDGE) OC lead edge
11 OC (FRONT/REAR) OC side
12 OC (TRAIL_EDGE) OC rear edge
13 SPF (LEAD_EDGE) SPF lead edge
14 SPF (FRONT/REAR) SPF side
15 SPF (TRAIL_EDGE) SPF rear edge
16 CIS (LEAD_EDGE) CIS lead edge
17 CIS (FRONT/REAR) CIS side
18 CIS (TRAIL_EDGE) CIS rear edge
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR)
4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR)
7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR)
[SCN]
10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR)
13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR)
16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR)
Press [START] key.
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
51
51-2
Purpose Adjustment
Function Used to adjust the contact pressure of paper on
(Purpose) the resist roller of each section (each paper feed,
duplex feed and SPF paper feed of the copier).
(This adjustment is required when the print image
position variations are considerably great or when
paper jams occur frequently.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Operation/Procedure
(Select the scan mode to be adjusted.)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 2 - 12.)
Set range Default
0 - 10 0
(Unit 1mm) (0mm)
1
0 3.OC(TRAIL_EDGE) 0
0 6.SPF(TRAIL_EDGE) 0
0 9.CIS(TRAIL_EDGE) 0
0 12.OC(TRAIL_EDGE) 0
0 15.SPF(TRAIL_EDGE) 0
0 18.CIS(TRAIL_EDGE) 0
Press [CUSTOM SETTINGS] key.
0
AR-M355N/M455N SIMULATION 9 - 62
Item
0 TRAY SELECT Paper feed tray
selection
1 PRINT START Copy start (Initial
value)
2 TRAY1 Tray 1 resist
adjustment value
3 TRAY2 Tray 2 resist
adjustment value
4 DESK Desk resist
adjustment value
5 BPT Manual tray resist
adjustment value
6 ADU ADU resist
adjustment value
7 SPF (HIGH) SPF resist
adjustment value
(High speed)
8 SPF (LOW) SPF resist
adjustment value
(Low speed)
2) Press [START] key.
(Resist adjustment)
1) Enter the resist adjustment value with 10-key.
2) Press [START] key.
When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.
Normal display
ERROR display Door open
Jam
Paper empty
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering the adjustment
value in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
Default
Set
AR- AR-
range
M355N M455N
1 - 5 –
– –
0 - 99 65 60
55 50
55 50
60 55
55 50
60 60
75 75
NOW PRINTING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed