Sharp AR-M455N Service Manual page 135

(Built-in finisher)
SIMULATION 3-3
FINISHER SENSOR CHECK.
PID SCID
SCPD POD
T2DN T2PD
STNC STHP
PSHP STUHP
STTHP2 DOPD
24VM MMLK
(Console finisher)
SIMULATION 3-2
FINISHER SENSOR CHECK.
FSSS FJS FFDSW FTCS
FSPS FSUC FSS FSTHPS
FULS FFE FFES FFRHPS
FBES FOBHPS FAS FRJHPS
FES
(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)
(FPDSS1)(FPTS)
( ) : Added when the punch unit is installed.
3-3
Purpose Operation test/Check
Function Used to check the operation of the load in the
(Purpose) finisher and the control circuit.
Section Finisher
Item Operation
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press START key.
The load selected in procedure 1 is operated.
Press [CUSTOM SETTINGS] key to stop the operation of the
load.
Built-in finisher
1 T2S Tray 2 solenoid
2 T2OM Paper exit motor
3 SPS Stopper solenoid
4 SCRS Roller pressure release solenoid
5 PPS Rear edge h folding solenoid
6 SCGS Compiler gate solenoid
7 STTM Staple rotation motor
8 STUM Stapler shift motor
9 MM Main drive motor
10 EVM Elevator motor
11 STM Staple motor
12 JRM Jogger motor rear
13 JFM Jogger motor front
14 PSM Pusher motor
Console finisher
1 FFC Folding clutch
2 FPSM Puncher side register motor
3 FPNM Punch motor
4 FLM Shift motor
5 FFSM Stapler motor
6 FSM Slide motor
7 FRJM Alignment motor R
8 FFJM Alignment motor F
9 FAM Bundle exit motor
10 FPM Paddle motor
11 FFM Transport motor
SCID2 PPD
T1PF T2UP
STSP STLS
JFHP JRHP
STTHP1
DSW1 DSW2
FFDS
FSHPS FLE FLLLS
FFHPS FFPS FSLS
FFJHPS FARHPS FPHPS
AR-M355N/M455N SIMULATION 9 - 9
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1-
Press [START] key, and the operation
is started.
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING .
3-6
Purpose Adjustment
Function Used to adjust the stacking capacity of the
(Purpose) finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
direction. The adjustment is made by changing the
alignment plate home position in the paper width
direction by software.)
Section Finisher
Item Operation
Operation/Procedure
Enter the adjustment value with 10 digit key pad and press START
key. The jogger moves to LT position (Inch series) or A4 position
(AB series) according to the entered value, and stops there.
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
Press [START] key, and the
operation is started.
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING ... .
3-10
Purpose Adjustment
Function Console finisher (AR-FN7) adjustment
(Purpose)
Section Finisher
Item Operation
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [START] key. (The entered value is stored.)
Item
1 Saddle binding position
adjustment
2 Saddle folding position
adjustment
3 Front alignment position
adjustment
4 Rear alignment position
adjustment
AND PRESS START.
2
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
2
50
Press [CUSTOM SETTINGS] key, and the
operation is stopped.
Stops when the operation is terminated.
50
Set Initial
1STEP
range value
0 - 400 200 0.0707mm
0 - 400 200 0.0525mm
0 - 20 10 0.367mm
0 - 20 10 0.367mm