Sharp AR-M455N Service Manual page 199

65
65-1
Purpose Adjustment
Function Used to adjust the touch panel (LCD display
(Purpose) section) detection position.
Section Operation (Display/Operation key)
Item
Operation/Procedure
Touch the four cross marks (+) sequentially. The coordinates of
pressed positions are set.
When the coordinates setting is completed normally, the display
turns gray. When all the four points are set, the display returns to
the normal state.
SIMULATION 65-1
65-2
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function Used to check the result of the touch panel (LCD
(Purpose) display) detection position adjustment. (The
coordinates are displayed.)
Section Operation (Display/Operation key)
Item
Operation/Procedure
When the touch panel is touched, the X and Y coordinate values
of the touched point and the coordinate values of the specified
point are displayed. The coordinate values set with SIM 65-1 are
used as the reference.
SIMULATION 65-2
100 200 300
100
140
180
66
66-1
Purpose Setting
Function Used to change and check the FAX soft switch
(Purpose) functions. (Used to change and check the
functions provided for the FAX soft switches.)
(Only when FAX is installed)
Section FAX
Item
Operation/Procedure
Setting of soft switches other than SW1 can be changed and
checked.
1) Enter the soft switch number to be checked or changed with
10-key.
The current set state is displayed.
400 500 600
40
600
200
AR-M355N/M455N SIMULATION 9 - 73
2) Enter the number corresponding to the bit to be changed with
10-key.
(Example) When the bit of 5 is to be changed, enter 5.
The set value of 1/0 is alternatively changed every time when
the target key is pressed.
3) After completion of setting of all the bits, press [START] key.
SIMULATION 66-1
FAX SOFT SW. SETTING. SELECT 2-120, AND PRESS START.
Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
SIMULATION 66-1
FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS
START.
SOFT SW-2:
66-2
Purpose Data clear
Function Used to clear the FAX soft switch function data
(Purpose) and to set to the default. (Excluding the
adjustment values.) (Only when FAX is installed)
Section FAX
Item Data
Operation/Procedure
1) Set the destination code with 10-key.
Japan 0 0 0 0 0 0 0 0
U.S.A. 1 0 1 1 0 1 0 1
Australia 0 0 0 0 1 0 0 1
U.K. 1 0 1 1 0 1 0 0
France 0 0 1 1 1 1 0 1
Germany 0 0 0 0 0 1 0 0
Sweden 1 0 1 0 0 1 0 1
Newzealand 0 1 1 1 1 1 1 0
China 0 0 1 0 0 1 1 0
Singapore 1 0 0 1 1 1 0 0
TW 1 1 1 1 1 1 1 0
Other1 1 1 1 1 1 1 0 1
Other2 1 1 1 1 1 1 0 0
Ohter3 1 1 1 1 1 0 1 1
The codes other than the above are recognized as Japan.
2) Press [START] key.
3) The confirmation menu of YES/NO of clear is displayed.
Select one.
1 YES FAX soft SW is cleared.
2 NO Not cleared.
4) Press [START] key.
The soft switch (except for the adjustment values) is cleared
according to the destination selected in procedure 1).
NOTE: When the FAX BOX is not installed, initialization including
the adjustment value is performed. (The adjustment value
is stored in the FAX BOX.)
1 2 3 4 5 6 7 8
Finland 0 0 1 1 1 1 0 0
Norway 1 0 0 0 0 0 1 0
Denmark 0 0 1 1 0 0 0 1
Netherlands 0 1 1 1 1 0 1 1
Italy 0 1 0 1 1 0 0 1
Switzerland 1 0 1 0 0 1 1 0
Austria 0 0 0 0 1 0 1 0
Indonesia 0 1 0 1 0 1 0 0
Thailand 1 0 1 0 1 0 0 1
Malaysia 0 1 1 0 1 1 0 0
India 0 1 0 1 0 0 1 1
Philippines 1 0 0 0 1 0 0 1
Hongkong 0 1 0 1 0 0 0 0