Sharp AR-M455N Service Manual page 185

4) Press [START] key.
Set range 25 - 200 (%)
(Table 1)
Item
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START (Default)
2 MAGNIFICATION Print magnification
ratio
(Lead edge adjustment value)
3 L4 Distance from the
front surface image
lead edge to the scale
of 10mm (SPF: 200%)
4 L5 Distance from the
back surface image
lead edge to the scale
of 10mm (SPF: 200%)
(Image loss set value: SIDE 1)
5 LEAD_EDGE Front surface lead
edge image loss set
value
6 FRONT_REAR Front surface side
edge image loss set
value
7 TRAIL_EDGE Front surface rear
edge image loss set
value
(Image loss set value: SIDE 2)
8 LEAD_EDGE Back surface lead
edge image loss set
value
9 FRONT/REAR Back surface side
edge image loss set
value
10 TRAIL_EDGE Back surface rear
edge image loss set
value
(Table 2)
Normal display
ERROR display Door open
Jam
Paper empty
(Table 3)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
When the total of the above set value and 10 is entered, the mode
is changed to the duplex mode (DD), and a duplex copy is made.
Set
Default
range
1 - 5 –
– –
25 - –
200%
0 - 999 –
–
0 - 99 15
20
0 - 20 0
0 - 99 15
20
0 - 20 0
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
AR-M355N/M455N SIMULATION 9 - 59
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 200
(ADJUSTMENT DATA) 3.L4
(IMAGE LOSS SETTING)
SIDE1: 5.LEAD_EDGE 15
SIDE2: 8.LEAD_EDGE 15
Select other than 0 - 2, and press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
PRESS START.
3.L4
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
Select 0, and press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 1-15, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 2, and
press [START] key.
SIMULATION 50-7
LEAD EDGE ADJUSTMENT(SPF CALC.).
(MAGNIFICATION)
INPUT 25-200(%)
50-10
Purpose Adjustment
Function Used to adjust the print image off-center position.
(Purpose) (Adjusted separately for each paper feed section.)
Item Picture quality
Operation/Procedure
(Print image off-center position adjustment)
NOTE: This simulation cannot provide an accurate adjustment. Do
not use.
1) Enter the number corresponding to the number of the paper
feed tray to be adjusted with 10-key. (Select one of 3 - 9.)
Item
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START (Default)
2 MAGNIFICATION Print magnification
ratio
(Off-center adjustment value)
3 TRAY1 Tray 1 adjustment
4 TRAY2 Tray 2 adjustment
5 TRAY3 Tray 3 adjustment
6 TRAY4 Tray 4 adjustment
7 BPT Manual feed tray
adjustment
8 ADU Adjustment when
paper is fed again
from ADU
2
160 4.L5 160
6.FRONT/REAR 20 7.TRAIL_EDGE
9.FRONT/REAR 20 10.TRAIL_EDGE
Press [CUSTOM SETTING] key.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
100
Image position
Set range Default
1 - 5 –
– –
25 - 400% 100
0 - 99 50
0
0