Sharp AR-M455N Service Manual page 154

25-2
Purpose Setting
Function Used to make the initial setting of toner
(Purpose) concentration when replacing developer.
Section Image process (Photoconductor/Developing/
Transfer/Cleaning)
Operation/Procedure
1) Press [START] key.
The developing motor rotates for 2 min and the toner concen-
trations sensor makes sampling of toner concentration 16
times, and the detection level is displayed.
After the developing motor stops, the average value of toner
concentration sampling is set as the reference toner concen-
tration level.
NOTE: When the above operation is interrupted on the way, the
reference toner concentration level is not set. Also when
error code of EE-EL or EE-EU is displayed, the reference
toner concentration level is not set normally.
(Default: 118)
2) The humidity near the developing tank at the developing
adjustment is registered.
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. PRESS START.
HUMIDITY AREA : 70.0 -
TEMPERATURE AREA: 70.0 -
DEVE REFERENCE : 118
Press [START] key. Press [CUSTOM SETTINGS] key, and the
operation is stopped immediately or after 2 min.
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. EXECUTING···.
HUMIDITY AREA : 70.0 -
TEMPERATURE AREA: 70.0 -
DEVE REFERENCE : 118
26
26-3
Purpose Setting
Function Used to set the specifications of the auditor.
(Purpose) Setting must be made according to the auditor use
conditions.
Section Auditor
Item Specifications
Operation/Procedure
1) Select the number corresponding to the auditor mode with 10-
key.
2) Press [START] key.
1 P10 Built-in auditor mode
2 VENDOR Coin vendor mode
3 OTHERS Other
4 VENDOR-EX Coin vendor mode (without temporarily
charge)
5 VENDOR-EX+ Coin vendor mode (without temporarily
charge) + Document filing function
enable
(Default: 1)
72.5
72.5
72.5
72.5
AR-M355N/M455N SIMULATION 9 - 28
SIMULATION 26-3
AUDITOR SETUP. SELECT 1-3, AND PRESS START.
1.P10
2.VENDOR
3.OTHERS
4.VENDOR-EX
5.VENDOR-EX+
26-5
Purpose Setting
Function Used to set the count mode of the total counter
(Purpose) and the maintenance counter.
Item Specifications
Operation/Procedure
1) Select the number corresponding to the counter to be set with
10-key.
2) Press [START] key.
3) Select the count mode with 10-key.
4) Press [START] key.
Set the count-up (1 or 2) for A3/WLT paper.
(Select the target counter.)
1 TOTAL COUNTER
2 MAINTENANCE (DRUM)
COUNTER
3 DV COUNTER
(Count-up)
1 1 COUNT UP 1 count-up
2 2 COUNT UP 2 count-up
SIMULATION 26-5
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS
START.
1. TOTAL COUNTER 1
2. MAINTENANCE(DRUM) COUNTER
3. DV COUNTER 1
Press [START] key.
SIMULATION 26-5
A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS
START.
1. TOTAL COUNTER
(1: 1COUNT UP, 2: 2COUNT UP)
26-6
Purpose Setting
Function Used to set the specifications (paper, document
(Purpose) detection, etc.) of the destination.
Item Specifications
Operation/Procedure
1) Select the number corresponding to the destination with 10-
key.
2) Press [START] key.
After completion of setting, the machine is automatically reset.
1 USA United States of America
2 CANADA Canada
3 INCH Inch series EX
4 JAPAN Japan
5 AB_B AB series B5
6 EUROPE Europe
7 UK UK
8 AUSTRALIA Australia
9 AB_A AB series A5
10 CHINA China
1
Counter
Total counter
Maintenance counter/ OPC
drum counter
Developer counter
Default
1
1
Press [CUSTOM SETTINGS] key.
1
Destination