Sharp AR-M455N Service Manual page 181

Item
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START
(Default)
2 MAGNIFICATION Print magnification
ratio
(Lead edge adjustment value)
3 L1 Distance from the
image lead edge to
the scale of 10mm.
(Platen 400%,
0.1mm increment)
4 L2 Distance from the
paper lead edge to
the image lead edge
(0.1mm increment)
(Image loss set value)
5 LEAD Lead edge image
loss set value
6 SIDE Side image loss set
value
(Void set value)
7 LEAD_EDGE Lead edge void set
(DENA) value
8 TRAIL_EDGE Rear edge void
(DENB) adjustment value
9 FRONT/REAR Front/Rear void
adjustment value
NOTE: When [P] is pressed after entering an adjustment value,
the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is per-
formed.)
Normal display
ERROR display Door open
Jam
Paper empty
(Copy condition in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
∗ To set the magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
Set range 25 - 400 (%)
Set
Content Default
range
1 - 5 –
– –
25 - 400
400%
0 - 999 –
–
0 - 99 15
20
0 - 99 35
32
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
AR-M355N/M455N SIMULATION 9 - 55
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS
START.
0. TRAY SELECT 1 1.COPY START
2. MAGNIFICATION 400
(ADJUSTMENT) 3.LT 320
(IMAEG LOSS SETTING) 5.LEAD
(VOID SETTING) 7.LEAD_EDGE(DENA)
8.TRAIL_EDGE(DENB)
Select other than 0 - 2, and press [START] key.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS
START.
3.L1
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). NOW COPYING.
Select 0, and press [START] key.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 2, and
press [START] key.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC).
(MAGNIFICATION)
INPUT 25-400(%)
50-5
Purpose Adjustment
Function Used to adjust the print image position and the
(Purpose) void area (image loss) on print paper. (Adjustment
as the print engine) (This adjustment is reflected
on all the FAX/printer/copy modes.)
Item Picture quality
Operation/Procedure
(Print image off-center position adjustment)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 9 - 14.) (Table 1)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed,
the adjustment value is set and printing is performed. (Table 2)
Check the off-center of the self-print patter of print-out.
(Shift for the adjustment value change: 0.1mm/step)
The greater the adjustment value is, the more the print image is
shifted to the front.
(Lead edge void area adjustment)
1) Set the lead edge void adjustment value (DENA) as specified
below.
(Standard set value) Paper lead edge void: 3.5mm (DENA:
35)
∗ Set the adjustment value of DENA to 35. Enter 35 as the
adjustment value of DENA, and press [P] key.
2
4.L2 105
15 6.SIDE 20
35
35 9.FRONT/REAR
Press [CUSTOM SETTING] key.
320
Press [CUSTOM SETTING] key,
or terminate copying.
Press [CUSTOM SETTING] key,
or terminate copying.
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
100
32