Sharp AR-M455N Service Manual page 125

b. Adjust the fax mode print density (standard mode/
small-character mode/super fine mode/600dpi mode)
This adjustment is intended to the print mode for each Fax mode
individually. In manual mode, the print density setting for each
print density adjustment level (1 to 5) can be adjusted to a custom
density level.
1) Set the test chart (UKOG-0162FCZZ) on the original table so
that it aligns with the front frame. Then put four or five pieces
of A3 (11" x 17") paper .
2) Go through the simulation modes that correspond to the Fax
modes for which to adjust the print density (i.e., the modes
specified in Simulations 46-13, -14, -15, -16, or -45).
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0
6.3.0 50 7.4.0
Select other than 0 - 2,
and press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND
PRESS START.
4.1.0
Select 1,
Press [START] key.
and press
Press [CUSTOM SETTINGS] key,
[START] key.
or terminate copying.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING.
Select 0, and press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
(ABOVE +20:DSPF MODE)
Select 2, and
press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0
6.3.0 7.4.0
1
50 5.2.0 50
50 8.5.0 50
50
Press [START] key, or
press [CUSTOM SETTINGS] key.
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
5.2.0
1
8.5.0
AR-M355N/M455N ADJUSTMENTS 8 - 16
Item
0 TRAY SELECT Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3 AUTO Auto
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0
6.3.0 50 7.4.0
9.AUTO(H) 50 10.1.0(H)
12.3.0(H) 50 13.4.0(H)
Select other than 0 - 2,
Press [CUSTOM SETTINGS] key.
and press [START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS
START.
4.1.0
Select 1,
Press [START] key.
and press
Press [CUSTOM SETTINGS] key,
[START] key.
or terminate copying.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). NOW PRINTING.
Select 0, and press [START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 2, and
press [START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0
6.3.0 7.4.0
9.AUTO(H) 10.1.0(H)
12.3.0(H) 13.4.0(H)
Set
Default
range
0 - 99 50
50 5.2.0 50
50 8.5.0 50
50 11.2.0(H) 50
50 14.5.0(H) 50
50
Press [START] key,
or press [CUSTOM SETTINGS] key.
1
Press [START] key or
press [CUSTOM SETTINGS] key.
5.2.0
1
8.5.0
11.2.0(H)
14.5.0(H)
1