Sharp AR-M455N Service Manual page 180

Normal display
ERROR display Door open
Jam
Paper empty
(Copy condition in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
∗ To set the magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
Set range 25 - 400 (%)
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
(ADJUSTMENT DATA) 3.RRCA
(IMAGE LOSS SETTING) 5.LEAD
(VOID SETTING) 7.LEAD_EDGE(DENA)
8.TRAIL_EDGE(DENB)
Select other than 0 - 2, and press [START] key.
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
3.RRCA
Select 1, and Press [START] key.
press [START] key.
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. NOW COPYING.
Select 0, and press [START] key.
SIMULATION 50-1
LEAD EDGE ADJUSTMENT. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 2, and
press [START] key.
SIMULATION 50-1
LEAD EDGE ADJUSTMENT.
(MAGNIFICATION)
INPUT 25-400(%)
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
2
50 4.RRCB 50 10.SIDE2 ADJ. 50
15 6.SIDE 20
35
35 9.FRONT/REAR 32
Press [CUSTOM SETTINGS] key.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key or
press [CUSTOM SETTINGS] key.
1
Press [START] key, or
press [CUSTOM SETTINGS] key.
100
AR-M355N/M455N SIMULATION 9 - 54
50-2
Purpose Adjustment
Function Used to adjust the document scan position, the
(Purpose) image print position, and the void area (image
loss). (Simple adjustment) (This adjustment is the
simple method of SIM 50-1.) (Document table
mode)
Item Picture quality
Operation/Procedure
(Lead edge image loss/void area adjustment)
1) Set the RRGB value of SIM 50-1 to 80 - 99.
2) Set the lead edge image loss adjustment value (LEAD EDG)
and the paper lead edge void adjustment value (DENA) to the
values specified below.
(Standard set value) Lead edge image loss: 1.5mm
Paper lead edge void: 3.5mm (DENA: 35)
∗ Set the adjustment value of LEAD to 15. (Enter 15 as the
adjustment value of LEAD and press [P] key.
∗ Set the adjustment value of DENA to 35. (Enter 35 as the
adjustment value of DENA and press [P] key.)
3) Set the adjustment value of L1 to 0. (Enter 0 as the adjustment
value of L1, and press [P] key.)
4) Set the adjustment value of L2 to 0. (Enter 0 as the adjustment
value of L2, and press [P] key.)
5) Make a copy at 400%, and calculate the values of L1 and L2.
(Enter 100 as the set value (MAGNIFICATION) of the copy
magnification ratio, and press [START] key.) (Place a scale on
the document table and make a copy.)
L1 = Distance (mm) from the image lead edge position to the
scale position of 10mm x 10
L2 = Distance (mm) from the image lead edge position to the
paper lead edge x 10
6) Enter the above values as the set values of L1 and L2. (Enter
the adjustment values of L1 and L2, and press [P] key.)
If the adjustment result is not satisfactory, perform the above pro-
cedures again from the beginning, or use SIM 50-1 to adjust.
NOTE: If a satisfactory result is not obtained with the above proce-
dures, through the adjustment values are changed individ-
ually, the normal adjustment cannot be made.
Perform procedures 3) to 6) continuously.
(Rear edge void area adjustment)
Adjust so that the rear edge void area is 3.5mm. (Change the
adjustment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjust-
ment value of SIDE, and press [P] key.)
When this adjustment value is changed, the image position is
shifted in the front/rear frame direction.
(Front/rear frame direction void area adjustment)
Adjust so that the total of the front/rear direction void areas is
7.0mm. (Change the adjustment values of FRONT/REAR, and
press [START] key.)
Front frame void area = 3.5mm
If, as shown above, the front and the rear void areas are not even,
use SIM 50-5 to adjust the image off-center position.
Image position
Rear frame void area = 3.5mm