Sharp AR-M455N Service Manual page 177

SIMULATION 46-46
SCANNER SHARPNESS LEVEL SETUP. SELECT 1-28, AND PRESS
START.
1:OC_NORMAL 3 2:OC_FINE
4:OC_SFINE 3 5:OC_SFINE(H)
7:OC_UFINE(H) 1
8:SPF1_NORMAL 3 9:SPF1_FINE
11:SPF1_SFINE 3 12:SPF1_SFINE(H)
14:SPF1_UFINE(H) 1
15:SPF2_NORMAL 3 16:SPF2_FINE
18:SPF2_SFINE 3 19:SPF2_SFINE(H)
21:SPF2_UFINE(H) 1
22:CIS_NORMAL 3 23:CIS_FINE
25:CIS_SFINE 3 26:CIS_SFINE(H)
28:CIS_UFINE(H) 1
Press [START] key.
SIMULATION 46-46
SCANNER SHARPNESS LEVEL SETUP. INPUT VALUE 1-3, AND
PRESS START.
1:OC_NORMAL
48
48-1
Purpose Adjustment
Function Used to adjust the copy magnification ratio (in the
(Purpose) main scanning and the sub scanning directions).
Section Optical (Image scanning)
Item Picture quality
Operation/Procedure
(Adjustment mode selection)
1) Select the number corresponding to the copy mode to be
adjusted with 10-key. (Select one of 3 - 7.)
2) Press [START] key.
Item
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START
(Default)
2 MAGNIFICATION Print magnification
ratio
3 CCD (MAIN) SCAN main scanning
magnification ratio
adjustment (CCD)
4 CCD (SUB) SCAN sub scanning
magnification ratio
adjustment (CCD)
5 SPF (MAIN) SPF front surface
magnification ratio
adjustment (Main
scan)
6 SPF (SUB) SPF front surface
magnification ratio
adjustment (Sub
scan)
7 CIS (MAIN) SPF back surface
magnification ratio
adjustment (CIS
main scan)
3 3:OC_FINE(H) 1
1 6:OC_UFINE 3
3 10:SPF1_FINE(H) 1
1 13:SPF1_UFINE 3
3 17:SPF2_FINE(H) 1
1 20:SPF2_UFINE 3
3 24:CIS_FINE(H) 1
1 27:CIS_UFINE 3
Press [CUSTOM SETTINGS] key.
3
Set range Default
1 - 5
–
– –
25 - 400% –
0 - 99 50
AR-M355N/M455N SIMULATION 9 - 51
(Copy magnification ratio adjustment)
1) Select the number corresponding to the copy magnification
ratio adjustment mode to be adjusted with 10-key. (Select one
of 3 - 7.)
2) Press [START] key.
3) Enter the copy magnification ratio adjustment value with 10-
key.
4) Press [P] key or [START] key.
When the [START] key is pressed, copying is performed and
the adjustment value is set simultaneously.
The copy magnification ratio in the sub scan direction can be
adjusted by changing the scan speed (motor RPM).
Normal display
ERROR display Door open
Jam
Paper empty
The greater the value is, the greater the correction is. One step
corresponds to 0.1% adjustment.
(Copy condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
selected paper with 10-key. (Select one of 1 - 5.)
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex mode.
∗ The copy magnification ratio can be set with the following
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
Set range 25 - 400%
NOTE: When [P] key is pressed after entering the adjustment
value, the adjustment value is set. When [START] key is
pressed instead, the adjustment value is set and copying is
performed.
NOW COPYING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed